3ET22DKXBW02 Whirlpool Refrigerator - Instructions

Looked up the process on you yube and watched the repair video from the parts website

snapped in the new end cap and snapped it into the fridge. I shouldn't have waited so long to order the part. it was cheap and easy to do

I put the end caps on the shelf bar and popped them into the slots on the refrigerator door. Very easy.
Good experience ordering from PartSelect. Glad I could make repair with minimal expense.

Removed all food and defrosted the evaporator. This took most of the time at about 2:30 hr. Replacing the gaskets only took about 30 min. this involved removing the small screws under the old gasket with a 1/4" nut driver in a drill/driver. Then removing the inner panal and pulling off the old gasket then cleaning every thing with warn soapy water and putting the new gasket on the inner panal and starting with the small holes, not the elongated ones, put the inner panal back on but don't tighten the screws down until you have them all in but loose. Then check that the door is strait with the unit, Set the clutch at 3-4 so you don't strip the screws, and start tightening them, checking that the door is still flush with the unit when closed as you go. Then do the same to the other door. That's it. No more frost!

First I called my friend Robert in Kissimmee, Fl to have an idea regarding the problem because I had never serviced a fridge before. Then he suggested that I check with PartSelect on the Web. Then PartSelect repair videos showed me everything. I followed step-by-step but the problem persisted. I finally realized that the airflow conduit between the freezer and the fridge was clogged with ice. I then proceeded to remove the ice underneath the coil on the aluminum cover and Bingo. The problem was in fact the ice. Well, I only spent $33 dollars for the non-necessary Bimetal Defrost Thermostat. I learned a great deal from that repair.

Pulled up part select video on u-tube. Followed instructions on dissambly of top freezer and found condensor freezing up blocking air from refrigerator. Checked timer to make sure it was good. Next checked continuity on heater to make sure it was good. Last checked bi-metal thermostat for continuity while cold. Found Bi-metal part to be defective (also rubber in top of was popped up which is a sign of a bad part). Simply ordered new part from Part Select, received in 2 days and replaced Bi-metal and melted ice with hair dryer and reassembled freezer. While waiting on part you can still use refrigerator by melting ice so air can get to refrigerator. I put a towel in bottom of freezer to catch water. Greg W. in Ga.

After watching the video it was a snap. Defrosting the freezer took the longest time. I used a hair dryer to melt the ice. Once the freezer compartment was clear of ice the removal and installation were a step by step procedure which the video showed in detail. It's been about a week since I installed the bimetal defrost thermostat and it seems to be working like new. Sure glad I researched this problem on the internet instead of calling a very expensive repairman! Thanks partselect. Com!!!

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

This problem can be caused by 3 different part failures. Timer, thermostat or heater. After contacting a service repair shop I was told that most often it is the thermostat. The cost of the repair would be at least $115. To much for an old refer. So I ordered the part from Partselect for $33. and put it in myself. Step1 cut the power to the refer. Step2 remove ice maker if you have one. Step3 remove base and back panels in the freezer. Step4 the coils were badly frozen so I used a hair dryer to thaw it out. Would have waited a long time for it to thaw out otherwise. Step5 The thermostat is clipped on to copper tubing next to the coils. Unclip it and cut the wires close to the thermostat. Strip the wires and wire nut the new thermostat. Clip it back on to the copper tubing. Put it all back together and start it up. It's over a week know and no problems. Note: We have whirlpool appliances that are over 16 years old. I have repaired the washer, oven, and now the refer with parts from Partselect. Good company. Always received the correct part within about 3 days from ordering. If you are able to do the work yourself you can save big bucks and keep your appliances running longer. Good Luck

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

Just instaling the new part with a screw driver

Removed items and defrosted freezer. I then removed metal shelves, ice maker, bottom sliding tray and false bottom, freezer back, and light bulb with wire track. Cut wires to defrost thermostat and spliced in new thermostat. Reassembled shelves, back, etc., in reverse order. Old thermostat tested "open" in hot and cold water with Ohm meter tester.

Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

I wasnt about to call Mr Appliance of Bayport NY the last time I called him I got a bill for $72.00 and he told me I needed a new frig. So I paid him then the next day I went to parts select and fixed it myself for about $50.00 But this time it was my Moms frig and the frig side (fresh food side) wasnt getting cold So again I went to parts select and put in a bimetel thermostat and it works perfect now. Im sure I saved a lot of $ and thanks to parts select, They helped me diagnose the problem and make the repair step by step! EASY! Thanks parts select...Garry from long island NY

We followed de video that made it very clear to us. Thank you! It's been working great since...