WRT108FZDM05 Whirlpool Refrigerator - Instructions

We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.

Discovered that the fan in the freezer was not working properly. Removed the ice maker, paneling, wire harness and inserted new motor. Worked immediately and began circulating the cold air into the refrigerator.

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

The icemaker came with very easy to understand instructions the installation took less than 45 min. that included installing the selinoid valve and waterline I had a nearby waterpipe, the acual icemaker took about 5 min. to install it in the freezer.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

First i pulled the electrical plug from the socket so the refrigator was off than I removed 5 screws (3 of those holding the ice maker). pulled the icemaker toward the front and removed it I than took off the back of the freezer panel,(the back panel was removed by pulling the top of the panal towards me it came right out of the freezer) I removed an additional 2 screws holding the evaporator fan motor. Than I used pliers to squeeze the mounting bracket tabs (white tabs BOTTOM OF MOTOR BRACKET). I then disconnected the electrical FAN MOTOR PLUG and removed the motor. i than pulled the fan blade from the motor (fan blade is only a pressed onto the motor shaft.I than pressed the fan blade back unto the fan motor and reversed the above directions

unplug, turn water off, remove ice maker & unplug,remove back panel remove old fan unit & unplug remove fan remove fan blades just pull off install new fan, put fan blades on new fan & install on bracket & re install plug in re install back panel. plug in ice maker re install ice maker . turn water back on plug refrigerator back in ( quite easy )

the repair it good and easy ,vo helper to do it.

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

Removed ice maker held on by 3 screws, took out 2 screws holding back panel, removed 2 screws holding bracket for fan motor, replaced evaporator fan motor and everything works great. Beware of thin splines, I have large hands and bummed up against them and slice one knuckle in 3 places which bleed profusely.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.

I actually followed the instructions by William. He did a great job. I ran into some difficulty because the wire connector on the replacement motor didn't match the old connector. We had to replace the connector on the new motor to match the wiring harness, which was easier than trying to match the connector on the motor. Had the connectors matched, the replacement would have taken less than 30 minutes to complete.

Added ice maker to our frige as i have never done one so i called a friend and he came over once we figured it out took less than 1/2 hour to install and run water line only thing instructions could have been a lettle clearer to under stand plus i called sears and they wanted 160.00 dollars for just the icemker this did not include the shut off arm or the bucket to catch the ice and there was no screws to attach it to the inside of the freezer you guys saved me $70.00 if not more and got more for my dollar thank you very much over all pretty simple check parts select before going to like sears or any place like them much cheaper here thanks