WRT541SZDZ00 Whirlpool Refrigerator - Instructions

Removed shelf, removed shelf frame and installed new one.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

Replaced inlet valve.

Getting the right part was the key but I had the serial number and the agent in Nova Scotia helped me identify the part and using the 360 degree camera, I was
able to determine how it was going to slide into the shelf. It took less than 15 minutes and was extremely easy to install. Everything just slide right in. The agent was the key to my success!

1)Removed the drawer
2) used a 8mm nut driver to unscrew the 2 mounting bolt.
3) clean /disinfect the bottom layer of the refrigerator
4) mount the track and installed the 2 #8 hex head mounting screw
5) slide back the drawer

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

The problem with the replacement part is that it didn't fit cleanly and doesn't slide well with the existing drawer.
We were disappointed.

I ordered a handle for my refrigerator and received a washing machine part. Still waiting after a week for my return request to be processed Not happy with the service.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

First, made sure new fan worked then Placed back in bracket with bushings-only goes in one way, pushed fan back on. screwed bracket to back of freezer and ran the wires to their original place, plugged in the two plugs, put the back piece up attaching ground and pulling ice maker plug thru, screwed back on. Plugged in ice maker, mounted ice maker on freezer wall. Plugged it in. Exact reversal of how it was removed. Not a lot parts to get confused.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

When I did not see instructions on how to replace the broken shelf that holds the meat drawer, I was afraid it would be difficult but after seeing how the broken piece placement was placed all I had to do was slide it off and place the new one. No problem, Thank you!!!

Followed instructions on your website

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.