WRF550CDHZ01 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from CAPE CORAL, FL
- Parts Used:
- WPW10714545
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket was old and air leaking into freezer !
Took off old one and just replaced new, very easy and corrected problems!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from LANCASTER, SC
- Parts Used:
- WPW10451500
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken door bin
Part select sent the WRONG part which I returned. They refunded the cost of the bin and tax but did not refund the shipping fee (which was paid to them for shipping me the WRONG part). i'm also out the shipping fee for sending the WRONG part back to them.
Installation was inconsequential; the service was terrible
Installation was inconsequential; the service was terrible
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Allentown, PA
- Parts Used:
- WPW10312696
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
not making ice
watched video
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from SMITH, NV
- Parts Used:
- WP12656018
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Tab broke off for chiller door.
Easy repair, nothing complicated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WALLA WALLA, WA
- Parts Used:
- WPW10300024
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
original ice maker would make ice and then water would over flow into ice bin and freeze
stick the very small screw driver in the hole on the left side cover and lift up to release the keeper tab,pull out to expose the wire connecter.insert the small screw driver in the slot on the left side to release the tab while pulling apart the two connectors.tuck the wires tight to side and pull out the ice maker.I thought I was getting the whole ice maker assembly,but just got a part of it,so I had take it apart and put it back together.the hardest thing to change over was the stop lever arm that senses the level of ice in the bin.after all this,it didn't work at all.not happy around here.back to filling ice trays
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOEL from LUMBERTON, MS
- Parts Used:
- W11671282
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
ice will not dispense ice from storage bin to out the door. Auger does not turn
Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Clinton, MA
- Parts Used:
- W10830055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Refrigerator seal was deteriorating, not sealing well.
I was hesitant to remove old seal, after I removed, I lined up new seal, and the seal popped into the slots very easily. Easy repair, no tools, worked great. The seal takes about 24 hour to seat itself for a great fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from N SYRACUSE, NY
- Parts Used:
- WP12656018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dropped a jar onto the pantry and broke the plastic piece on end cap that moved the drawer lid.
Removed the lid and pantry drawer. Removed crisper drawer on right side and glass shelve. Removed 2 screws on glide. Removed 2 nuts with nut driver. Gently tugged on the pantry end cap and it released from the back wall. Had to rotate about 90 degrees to remove the extension off the back wall so I could remove the thermostat control arm from old piece and put it onto the new piece. Gently removed the thermostat control through a series of squeezing pieces and rotations. Do not force anything. Take your time as you are working with plastic that could break at any moment with force. Replace in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from E GRAND RAPID, MI
- Parts Used:
- WP12656018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Bottom drawer access door hinge pin broke of pantry end cap - right side. The pin(knob) is a molded part of the end cap.
Removed two 1/4" screws from the end cap with the nut driver and removed it. Transferred a few pieces from the old end cap to the new. Reinstalled the new end cap and presto, job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from RICHMOND, IN
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door on the pullout lower "Pantry" had cracked
Part was pretty ubiquitous so plastic door pins part fits a lot of refrigs, no tools necessary, new part is flexible enough to bend slightly to fit over pins at side. Mine was a bottom freezer type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Port Aransas, TX
- Parts Used:
- WP12656018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The pin on the right side of the Deli Drawer full width door broke off
I removed the Deli Drawersvegatable and fruit drawers. Removed the glass panel. Removed the screws holding the Endcap and snapped the old one out. A back panel strip that controls the humidity snapped out. I installed the back panel to the new endcap. Installed the new endcap snapping it in place and used the screws to keep it in place.
It was not difficult and everything fit perfectly. The only thing it takes is a little understanding as to how it all fits together. It took about 20 minutes.
It was not difficult and everything fit perfectly. The only thing it takes is a little understanding as to how it all fits together. It took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Plattsburgh, NY
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Cracked lid, broken hinge - right side
Two phillips head screws out to remove drawer slide. Three screws to remove right side drawer support. New support placed, new lid snapped into place. The right side has an adjustment lever. Re-routing that took the longest. The arm had to be removed and twisted to get the adjustment knob off and on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Grants Pass, OR
- Parts Used:
- WP12656105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
I broke the pin that holds the lid that covers pantry at the bottom of the fridg.
I removed the drawers above and the glass shelf, then removedthe screws to remove the broken end cap then reversed the proceedure to install the new part. Was simple to do and it works fine.
Was this instruction helpful to you?
Thank you for voting!
Empty box sent with no part!!!! No customer service help because of covid
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from ST CLR SHORES, MI
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
needed to replace water filter
unscrewed old filter, screwed in new....good to go!
Was this instruction helpful to you?
Thank you for voting!