Models > WRX735SDHZ01 > Instructions

WRX735SDHZ01 Whirlpool Refrigerator - Instructions

Jump to:

All Instructions for the WRX735SDHZ01
91 - 105 of 248
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Charles from SEGUIN, TX
Parts Used:
W11291138
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Repaced the right-side door light switch
Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back on and checked the switch. Worked perfectly! Easy job.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from SWANVILLE, ME
Parts Used:
W11338583
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Freezer Bulb failed
Unscrewed bulb from sock .
Replaced with new one . Now working
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jerry from GAMBRILLS, MD
Parts Used:
W11043011
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
the light in the Fridge starting blinking like strobing on and off
I looked up part found parts select, ordered, opened fridge doors put tape over door switch to keep light off, or just hit the turn light off on panel, unscrewed LED light, whick is a led circuit card and not a blub.
snapped it out - snapped new one put retaining screw in , removed tape and WA-LA...
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rodney B. from Crestview, FL
Parts Used:
W11395888
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Filter stopped up. Causing the refrigerator to make a loud noise. water dispenser didn't work. less than 4.00 fixed all that
Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Matthew from Pensacola, FL
Parts Used:
W11291138
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light switch broke
Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mike from New Johnsonville, TN
Parts Used:
W11291138
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light switch broke.
Couldn't figure out how to get the old one out till I saw the new one.Pop the old one out slide the 2 wires on the new one pop it back in place,good to go.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eric from Noank, CT
Parts Used:
EDR4RXD1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Replacing filter
Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from Oro Valley, AZ
Parts Used:
W11396033
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Catherine from BROOMALL, PA
Parts Used:
W11396033
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
HARRY from FSTRVL TRVOSE, PA
Parts Used:
W11396033
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Grafton, MA
Parts Used:
EDR4RXD1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Ice machine was not making ice
Changed the ice and Water filter, works great...
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from MABLETON, GA
Parts Used:
W10619951
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Easy fix for Whirlpool refrigerator
I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from ST CLR SHORES, MI
Parts Used:
EDR4RXD1
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
needed to replace water filter
unscrewed old filter, screwed in new....good to go!
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOEL from LUMBERTON, MS
Parts Used:
W11671282
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
ice will not dispense ice from storage bin to out the door. Auger does not turn
Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wayne from Red Banks, MS
Parts Used:
12002497
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken Freezer Drawer Gear
Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WRX735SDHZ01
91 - 105 of 248