WRF532SMHZ02 Whirlpool Refrigerator - Instructions

Bought new crisper from Parts select followed directions on how to replace. Replaced in a bought 30 minutes.

Motor evaporate. Replacement. Just like the video and it worked out perfect. Refrigerator works great now.

Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.

This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!

with the freezer working I knew the compressor was working. I confirmed that the actuator door in the refrigerator was working but no air was blowing out. The hardest part was removing all the freezer drawer components and the ice maker so I could remove the panel in the back covering the evaporator motor. A quick resistance check of the motor confirmed no continuity in the motor. Take your time so that you dont break any of the snap in pieces. The motor I received did not look like the one I was replacing, but in fit in place and bolted right in. They provided an adapter wire to connect the wiring. All in all it was a fairly easy job. The video I followed was very helpful.

Removed rear cover, removed fan and than drip tray. install new tray and reassemblied

Looked at several videos on line in order to learn how to remove door and and all trays and bins and remove ice maker. Mostly straight forward. It helps to have a second pair of hands and eyes to assist. But could be done alone.Never did this before but I would say that, with a little courage, anyone could do this. I had a local repair estimate of almost $300. I did the job for the cost of the part, $80.

Replaced ice maker, but new one drips.

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

Tested things a saw that the water valve was working so I figured it had to be the unit in the fridge. There was a possibility that it could be the thermostat or a couple of other possibilities. So I decided to replace the entire unit. That would be easiest and for sure solve the issue. It was simple since the new unit contained everything including the wire harness. So all I had to do was un plug the wiring connection remove 3 screws, remove the unit, put the new one in and plug the wiring connection in. Done in a couple of hours had ice. Within in about 24 hours ice tray was full. And works well

I replaced the icemaker assembly.

Just take the crisper out and just put it in the hall access

Checked a video on YouTube and found questions and answers to this concern.. All lead to the compressor capacitor. Entered part # on your Website. Capacitor come right up and also suggested a Start Device. I ordered both parts as I was not sure if these parts would fix my problem.
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..

Removed the plastic frame, washed the frame and fridge, set new glass into the frame.