WRF532SMHB01 Whirlpool Refrigerator - Instructions

I first removed the door to the freezer (my frig has a bottom freezer) by loosening the 4 screws and lifting the door up and off. Then, because I'm stubborn, I chose not to remove either of the basket/drawers. It took a little bit of effort to fit my arms/hands in there, but I was able to remove the bottom screw to the old icemaker, and loosen the two top screws. (And disconnect the wiring harness.) I could then lift the old icemaker up and off. Putting the new icemaker in was pretty easy-- just slide it down over the two top screws and connect the wiring harness. The hardest part was getting the bottom screw back in! Because I didn't remove the baskets/drawers, I had very little room to work, and I had to "feel" for where that bottom screw went (even used a little mirror to help me). I could have just left this screw out, as the icemaker was sitting in there quite securely. But I kept at it, and after about 20 minutes, I was able to line up the screw with the hole, balanced on the tip of the screwdriver, and get it screwed in. Total repair took about 45 minutes. And no more leaky ice maker!

Unplug the electric flat plug from wall. Loosen up 3 mount support screws , Change out unit. Mount Int back onto 3 support screws . Plug in electronic flag plug , It only goes in one way since the plug as a grove on it.

This could have been a 5 minute repair if the shelf frame had included the U shaped metal piece and the front curved snap on decorative piece. I had to break the old frame, slide out the U shaped piece, insert it into the new frame then carefully snap off the decorative curved piece and attach it to the new piece. You would think for $100 it would be the complete set. The shelf did not support the weight of the drawers without completing these two additional steps.

I pulled off the old gasket and placed the new gasket in the existing groove, shut the door; problem solved!

By sliding athin screwdriver blade down the side of the old switch the expasion prong that hold the switch in place was compressed enough to allow the switch to come out easlily. Plugged in new swithc and snapped in place. Plugged the refrigerator back in and light has worked great sense!

The video was a great help. I was able to replace gaskets on both doors with out taking them off and no tools were needed.
One of the refrigerator doors has a plate that closes with the door that makes replacing the gasket questionable but I was able to do it with no problem.

I first replaced the lower (freezer) evaporator thermistor based on recommendation from other feedback, however that did nothing to resolve the problem. I subsequently discovered a diagnostic document hidden under the upper right door hinge, which helped me narrow the problem down to the upper (refrigerator) evaporator fan motor. After replacing the fan motor, my refrigerator is up and running again. The only challenge was accessing and removing the access panel(s) and air column. Once those were removed, replacing the fan motor was simple.

Ordered the part. When came in I took it out of the box and slid the two end posts into the provided holes. Lid fixed in less than 5 minutes. Part came in on the third day because I ordered on Friday afternoon.

I did not unplug the refrigerator. Your choice on this. Take a close look at the existing icemaker, how the wires are routed and what the water spout looks like as it relates to the icemaker. Small flat-blade screwdriver will help in unlocking tabs on the icemaker plug. Go ahead and unplug it. Of the three screws that secure the icemaker, two are impossible to see without holding a mirror in your third hand. Completely remove the bottom screw (by feel). Don't drop it, like I did. Have no idea where it went. Loosen the top two screws but do not remove. Icemaker will lift off of the top two screws when you push it up. With old icemaker out of the way, plug in the new icemaker. Be careful to properly align the water spout into the new icemaker as you hook it on the two top screws. When everything looks good, tighten the two top screws. Replace the bottom screw, if you didn't lose it. My icemaker is doing fine without a bottom screw. It should make some ice within an hour, or so. Mine did.

We snapped the new one on correctly this time.

Hardest part is access to the icemaker itself. Once I removed the freezer door (bottom drawer freezer), and got the sliding basket out, it was a 10 minute job. Make sure you start the upper screws first, the icemaker will hang there while you adjust, connect the harness, and tighten. Make sure you are ready before you close the door, it will start making ice as soon as the door is closed.

Used a deep well 1/4" nut driver. Loosen 4 screws on inside of door and slip it up and off rack. Remove 2 screws on bottom of ice maker. Loosen top 2. Slip up of screws, unplug ice maker and remove.

You just take the old door bin out by sliding it up and replace with the new bin by sliding it down in the door.

Awesome! Couldn't ask for it any better. I watched the video from Partselect multiple time and was just as easy as they said it would be. It took me longer to watch the video four times than it did for me to install it. I have a habit of 10 minute projects turning into a couple hours and this took about 10 minutes. Thanks.

.screw held in the center of the rail,pull it out,slide the rail up off the support brackets on the door,unplug the old one & plug in the new one,slide on, & replace the screw! That Easy