WRS312SNHW01 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jean from Valley Mills, TX
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The ice machine quit working.
It was so easy. This is the second Ice maker we have put in this fridge. Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Manchester, NH
- Parts Used:
- W11700559
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Wrench (Adjustable)
whirlpoolAuto Ice maker not working
Whirlpool refridgerator, parts were not exactly the same,but did fit. The electrical hook plug was perfect. Old ice maker had wear marks in channels. Installed new ice maker. Pump still didn't operate after letting ice box get down to normal temp. Replaced pump. Had to use hose permanentely attached to new pump. Removed old hose and clamped new hose at top and outside refrigerator with existing clamp. Let the freezer get back down to normal temp. Ice maker operated perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheri from Muskogee, OK
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
never had an icemaker attached
My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BreathMinder from Merritt Island, FL
- Parts Used:
- W11700559
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Didn't work once installed
Installation went smooth - only three hex-head screws (one below unit and two above. After removing 3 screws, unit comes loose in your hand but is still connected by a plug leading 4 wires to a connector visible through a slot in back panel of freezer compartment. New unit goes in easily (making sure spout from pump that protrudes from back wall fits through opening on icemaker) but there's not a generous amout of wiring harness and the 'female' of the electrical connection is recessed and loose inside a cutout in the rear panel so you can't get a good grip on it nor can you feel if it plugs securely. I plugged new unit into connector and then secured it with the 3 screws, waited the 12 hours per instructions, but no ice. Removed unit and guessed that the plug had not seated fully (not plugged in.) I took a short piece of a wooden paint stirrer and put it on back edge of plug and tapped it into place so it seated fully. Immediately, the pump cycled and water came from the filler spout, so I surmised that it was now properly plugged in - it began making ice in a couple of hours and has operated perfectly ever since. Lesson learned is to make sure you get the electrical connector fully in place - mine did not 'snap' or 'click' into place and I wrongly assumed it was plugged in correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Petersburg, AK
- Parts Used:
- W11700559
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Wrong valve bracket
I completed the ice maker installation but the bracket the automatic water valve was attached to in no way would fit my Whirlpool fridge. The one showed in instructions sent with the ice maker was different than the one Partselect sent me. I had to grind both sides of the bracket off and just hot glued it to the spot where it was supposed to go. I can see how this could be a real issue for some.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Burnsville, WV
- Parts Used:
- W11700559
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
The wire harness plug was male .Same as the plug on the refrigerator
I cut the plugs off and bought male and female wire conectors and crimped them on the wires and pluged them together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- oliver from tampa, FL
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
old ice maker the ice cubs keep freezing togather
replaced old one installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dora from Rock Island, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light would come on and off
Viewed the viedo - it showed what to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from River Edge, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
exchange of defective light rocker switch
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Fairport, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light in the refrigerator didn't work
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Fort Worth, TX
- Parts Used:
- WP2309941
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom door shelf bracket cracking
unsnap old part and gently push new shelf bracket in till it snaps into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Bowling Green, MO
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Heater not releasing ice
Removed/replaced ice maker and valve per enclosed instructions. If you can service your own lawn mower this R&R should be easy for you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from Yuma, AZ
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old ice maker not working right
Per instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Aliquippa, PA
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice maker was not performing correctly after cleaning freezer and refrigerator.
Unplugged refrigerator. Unplugged ice maker and took out three screws holding ice maker. Put new ice maker and attached three screws. Plugged ice maker in. Plugged refrigerator in and ice maker began working. Threw out first ice cubes made. Unit now working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Leesburg, FL
- Parts Used:
- WPW10119935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light wouldn't go on
Pulled socket out of housing, unplugged it from source, plugged in new socket and replaced the socket into housing, screwed in bulb and it worked!!
Was this instruction helpful to you?
Thank you for voting!