WRS312SNHM01 Whirlpool Refrigerator - Instructions

took old one out with a screw driver,replaced it with the new one. works great!. din't have to put part on at back bottom.I will say this.you guys sure got the part here fast! thanks..

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Simply removed the old icemaker and replaced it with the new one. Reqires removing 3 hex head screws and wiring harness, then reconnecting the new unit.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

I got the part....I put it in. That's about it.

googled the model of ice maker and refrigerator, ordered replacement ice maker from Part Select. Received next day, installed it in 10 minutes and it worked like a charm.

Remove back cover. Slide blade off, slide new blade on.

I removed a few items from the freezer to make room. Husband took out the old ice maker. (We were sure it would require moving the refrigerator out which would have been a huge undertaking given the tight fit) To start he simply replaced the ice maker with the new one. I started watching...and even though it says that it will take up to 24 hours to make ice, it began making ice probably within an hour! After about 6 batches, I threw those out. (just in case there was anything in the line that would contaminate the cubes)It is obvious that the old one had not worked properly for a long time! The ice container is full to almost over-flowing! It has not been this full in a very long time, as I use ice every day! Simple fix! And might I add...LIGHTNING FAST DELIVERY!! It was here in two days! We are thrilled!!!!!

I watched your repair video, read the instruction enclosed with the icemaker and made the repair in about 15-20 minutes. There is an issue that others need to be aware of once the water pump is repaced and the tubing is connected and the icemaker is installed and turned back on; it take 20-30 minutes to pump the air out of the line and the for the water to actually fill the the fill tray (you made the install correctly, the delay in filling is not covered by either the video or the book just be patience don't disconnect and reconnect anything it will eventually fill and make ice and less than 48 hours). This vendor offers 4 star customer service at a fair and resonable price (I priced the parts separately prior to purchase and the kit is the way to go). I received the product within 3 days, shipped groung delivery. I would use your products and online service advice for installation on other appliances in the future if needed. You have earned my trust, and repeat business in the future; and I will gladly recommend you to others. Your customer focus and service is second to none. I am a fully satisfied customer!!sincerely, a. Walker

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.

The icemaker came with very easy to understand instructions the installation took less than 45 min. that included installing the selinoid valve and waterline I had a nearby waterpipe, the acual icemaker took about 5 min. to install it in the freezer.

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.