WRF560SEHB00 Whirlpool Refrigerator - Instructions

First I removed the (3) screws holding the unit to the side of freezer wall with a nutdriver. Then I disconnect the Harness from the back of the freezer. You have to work the Harness off connector because it was very tight. The Unit came with the correct harness installed so I reconnected the harness to the Freezer and replaced the (3) screws. I had ice in about 2.5 hours.

It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reattached the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.

removed the three screws holding the old ice maker in place - unpluged the electronics .... took the new ice maker pluged in the electronics screwed in into place and we were in business and had ice within an hour.

At first ordered the wrong part. Using the website was difficult to find the correct part, but once I called, it was pretty easy to find the part needed. Part showed up and install was only a few minutes. No more leaking!

Thanks for the help PartSelect!

That 1 Phillips screw out push up disconnect electrical plug put new one in by going in the opposite way.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Just like the others. Unplug the refrigerator. Loosen the top two screw and remove the bottom screw. Unplug the unit, plug in the new one, slid the unit over the top two screws, replace the bottom screw and tighten the top two screws. Done. I ordered the unit Sunday it was shipped Monday and arrived Phoenix Wednesday, shipper then rerouted it to Tucson Thursday who sent it back to Phoenix on Friday and finallydelivered it Saturday.

First I removed the ice bin to give me room to work. Then I took out the screws that held the old ice maker in place. I disconnected the wiring. I then plugged the wires of the new ice maker into the old wiring harness. I put in the bottom screws and loosely connected the top screws. I checked the level of the ice maker with a small level and then tightened the screws. The nest thing was to install wire level that shuts off the ice maker when the bin is full. Finally put the ice bin back in place.

Super easy! I read all these posts but here are a couple helpful hints -

1. to remove the old icemaker definitely remove the one lower screw but then unscrew the top two screws only half way. The top screw holes on the old and new icemakers are triangle shaped so the old icemaker will simply lift off the half-unscrewed top screws. This makes reinstallation SO much easier.

2. carefully lower the loose icemaker enough to disconnect the wiring harness from the fridge and remove the old icemaker.

3. On installation the one thing to be careful with is the positioning of the fill tube. It's easier if it's in place when you reconnect the harness of the new icemaker because the harness is only as long as it must be.
4. hang the new icemaker on the half unscrewed top screws, snug them up, install the lower screw and flip the wire ice level sensor arm down.

I didn't even turn the water off because only a working icemaker can turn the water valve on and off.

Plugged in the power to the fridge and within an hour water filled the tray. By morning I had 2-3 batches of fresh ice in the bucket. Super easy.

I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in less than 24 hours from my order placement.

Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour

Very simple fix, remove 3 screws, two connectors to the old switch

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel

I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks