KRFC300EBS01 Whirlpool Refrigerator - Instructions

A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Snapped in new part

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

I followed the remove and replace instructions in the Part Sect video when I ordered the seal. Pulled out the old seal by hand and installed the new seal. No tools needed, very easy. Took 10 minutes at most.

Unscrew decorative plastic cover. Unsnap old damper assembly and disconnect wire connector. Snap in the new assembly and plug in the wires. Replace decorative cover.

Turned off power, Removed screw, disconnected wire harness and removed old rail from door, Connected new wire harness and attached new rail to door, replaced screw. Restored power. Done.

Very easy to fix . It was harder to empty the contents out or the refrigerator than to repair . The diagrams on this site were very helpful in identified the part. and it was delivered in 5 days.

Got the right part on the second try but am so happy I did it myself. Easy install 3 screws and a plug. A little hard to reach in bottom drawer freezer but making great ice now.

removed the freezer door, removed the two shelves and removed three screws from the icemaker, unplugged the wiring harnest. Installed the new icemaker in reverse procedure.

Let the ice in the freezer melt while installing P trap drain tube

I brought you the exploded view of the crisper parts on your website and proceeded accordingly. Besides the three nuts holding the end cap to the frig interior wall the temperature adjustment linkage had to be disassembled on reassemblied on the new replacement end cap. Plastic linkage parts present the problem of breakage, so one must be careful during the disassembly process. Some other type of fasteners for the linkage assembly (screw and nut, ball and socket) would be prefereable. All and all, its a machine. Wtith exploded view, what could go wrong?

Loosen the 2 mounting screws on the top about 2 turns; take the one mounting screw on the bottom all of the way out. The top part of the ice maker drops down on the loose top screws. That holds the ice maker while installing the bottom screw. No need to shut off water to the ice maker, just shut off electricity to refrigerator.

When the gasket is delivered it will be folded. You will need to unfold it and leave it on a flat surface for several days. Keep it as square as possible, and heat the kinked portions with a hair dryer on high heat and slow fan while molding kinked portions with your hands for 30 to 60 seconds at a time. Do that 2-3 times per day. When it looks 90% uniform with the non kinked portions, you can install it. Installation takes less than 10 minutes. Clean the metal edge of the freezer well. I recommend taking the door annd frame off (This is remarkably easy. THe door and frame pretty much lifts up and out after you hold the rail clips inward) because the lower edge is so close to the floor. The just pulll off the old gasket. There are no screws or clips. Starting in any corner, press new gasket into place. Go around the perimeter several times to make sure it is pushed in fully and evenly. Then reinstall the door and frame.

Access back of unit, lower left corner. Remove wire capacitor retention clip. Unplug cold capacitor, plug in replacement, reinstall wire retention clip, test.