WRS335SDHW00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gail from Golden, CO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BONITA SPGS, FL
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
install ice maker 2 screws wire harness pluged in done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from LANCASTER, SC
- Parts Used:
- W11239961
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace cracked refrigerator shelf
Just took a minute to put new shelf in place.... easy peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randolph from Derby, KS
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Auger blades separated from hub.
First I removed the screw holding the ice door shaft (at the rear of the ice container). Removed clip of which the screw was holding in place (no need to remove the clip from the shaft). Then I removed the front cover screws, separated front cover from ice container. Door shaft is removed with front cover assembly, no need to remove anything else from front cover. Pulled out auger shaft, removed circlip (snap ring) and washer from front of shaft. Used an adjustable wrench to remove plastic nut from front end of shaft. CAUTION - the plastic nut is reverse thread, make sure to turn it clockwise to loosen and remove. Pulled off broken auger then reassembled with new auger in the reverse order as previously described.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Goldsboro, NC
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice bin auger drum fins broke off from the main shaft,stopping the production of crushed ice.
Replaced the Ice Bin Auger,I ordered from PartSelect,which had much thicker housing and fins than the original .You remove the clip from the end of the shaft and a nylon nut which is a left hand which is opposite threads from most nuts.Its a good idea to take a picture of how the blades and spacers are ,because if not put back in the same direction their will be no crushed ice.It now works better and quiter than when it was new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominique from BURLESON, TX
- Parts Used:
- W11188040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Broken glass shelf top
I remove the shelf above of the one that needing repair as well the one that required repair. I carefully place the white shelf frame into the rubber seals on the glass . Thirdly placed everything together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Port Orchard, WA
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Changed the filter
Took the old one out and put the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from ROSWELL, GA
- Parts Used:
- 4388736
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The original was broken.
Take it apart, replace with the new one, put it back together. So simple even a democrat girl could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CRAIG from UNDERWOOD, MN
- Parts Used:
- W11371713
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Holder broke along side towards the front
Slid weatherstripping off old and slid it on to new, replaced it into fridge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merrill from CHULA VISTA, CA
- Parts Used:
- W11162448
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken plastic drawer
Pull out old drawer, push in new drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from WILLIAMSTON, NC
- Parts Used:
- W11188040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Added another shelf
Just slid it in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SALINA, KS
- Parts Used:
- W11700559
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
3 screws
Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from JACKSONVILLE, NC
- Parts Used:
- WP1119017
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice deflector had broken.
Removed ice tray and unbolted front cover. Removed broken piece and snapped new ice deflector in place. Reinstalled front cover and put ice tray back into freezer. Cycled crushed ice, works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from MURFREESBORO, TN
- Parts Used:
- W11162443
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The crisper drawer has broken.
It was just a matter of pulling the old drawer out and sliding the née drawer in place. Ron was very helpful when ordering it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from HOPATCONG, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this instruction helpful to you?
Thank you for voting!