GB2SHDXPB00 Whirlpool Refrigerator - Instructions

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Instructions were great five minutes to remove and replace fan....Thank You............ saved big money

took about 15 min just took off gasket with flat screwdriver cleaned and put it on no glue it has magnets very easy

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

My Freezer would only auto defrost occasionally and I first thought it was the defrost timer. But after reading posts on this website I looked deeper and found that my Defrost thermostat was bulging out. That didn't seem right just by looking at it. I read an earlier post and figured that must be it. I received the part and did the repair in about 15 minutes just had to cut two wires and reconnect with wire nuts and clip thermostat back onto the copper tube. Works perfectly now!

just pop the old one out popped the new one in its replace.

I initially tested the heating element and defrost thermostat using an ohm meter. the defrost thermostat was incased in ice, so I replaced it first. The refridgerator worked for about a week and then froze up again. I then replaced the thermistor and the unit is working as designed.

Thermostat kit it only had one connector. Fortunately I had a small wire nut that I used on the other wires.

My freezer compartment gasket was torn and needed replacement. This was on a bottom freezer Kenmore refrigerator. I couldn't find directions for how to take the freezer compartment door off, and figuring out how was the hardest part. Here are the instructions:
1. At least 24 hours prior to starting, remove the gasket from the packaging and lay it out in a warm area, to allow the creases to come out.
2. Unplug the refrigerator.
3. You will have to take BOTH doors off, so put at least the freezer compartment contents in a cooler so they don't thaw. Also remove all items from the refrigerator and freezer door.
4. Remove the refrigerator door first - remove the plastic cover from the top hinge, then remove the 3 metal screws holding the hinge in place. Lift the door up, and it will come right off. Set it aside.
5. Now remove the freezer door - there is one bolt head, for the top hinge pin. Remove it, and lift the door up and put it down on a table.
6. Towards the center, pull up on the old gasket, and use a pair of diagonal cutters to cut it in half. It will take a few cuts, but eventually you will get it out and cut in half. Then remove the old gasket.
7. The new gasket simply presses in. Start at two diagonal corners, then press the other two corners in, then do the straight sections.
8. Now replace the freezer door, then the refrigerator door, plug in the refrigerator, and put the contents back in.

Replaced the relay and capacitor it runs.

long story, but good experience with Partselect.com...ordered a defrost heater as I had to replace same 15 years earlier, when part arrived I managed to test continuity of old heater in place and appeared fine (unless due to intermittent break that opened with heat) - so went ahead and order defrost thermostat and arraigned for return of heater (kept until testing after installation of the thermostat) - replacement of thermostat pretty easy - be sure to watch video of how to remove freezer rails for bottom freezer.
When I plugged back in the compressor wouldn't start, tried to and then shut off over and over. I had the dreaded thought that either I had put a leak in the coils or the compressor had failed due to overwork with failed defrost mode. Fingers crossed I ordered start capacitor and relay kit...sure enough when I removed the old capacitor and relay - I heard loose parts in the relay and pieces fell out when I shook it. installed new relay/capacitor and the fridge works like new - 21 year old Amana - very well engineered and easy to work on - great videos on disassembly re-assembly - when I replaced the heater 10 years ago I couldn't figure out how to remove side rails - no idea how I managed to pull the bottom of the cooling unit past the rails to remove and replace the heater.
I would recommend doing what I did, unless you are sure of the failure mode - which is to leave the back panel open for a day in the freezer after repair to be sure the defrost mode is working.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

replaced inlet valve per insert with part, easy

Very easy to order from parts select. Took seconds to replace.

First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Refer to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!