8ET1WTKXKT05 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from HOUSTON, TX
- Parts Used:
- 4387478
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Faulty light socket
Followed the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted C from DSRT HOT SPGS, CA
- Parts Used:
- WP4387503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drain clogging causing water to leak bottom of fridge
After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from WINSTON SALEM, NC
- Parts Used:
- WP2176225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The handle broke and my wife was afraid to close the door because she might not be able to open it back.
The part-select video showed me to do the following:
Unplug dish washer
Open the door and unscrew the screws around the inside of the door all around.
Place the screws in the detergent holder with a cap until finished.
The door mechanism is at the top and attached to two electrical wires.
Unfasten the wires from the attachment.
Take the new attachment and fasten the wires to it.
Place the attachment back in the spot and make sure handle is sticking thru the hole to the outside.
Reattach the screws.
Plug back chord.
Finished - 15 minutes
Unplug dish washer
Open the door and unscrew the screws around the inside of the door all around.
Place the screws in the detergent holder with a cap until finished.
The door mechanism is at the top and attached to two electrical wires.
Unfasten the wires from the attachment.
Take the new attachment and fasten the wires to it.
Place the attachment back in the spot and make sure handle is sticking thru the hole to the outside.
Reattach the screws.
Plug back chord.
Finished - 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from SWANVILLE, ME
- Parts Used:
- W11338583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer Bulb failed
Unscrewed bulb from sock .
Replaced with new one . Now working
Replaced with new one . Now working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from KAUFMAN, TX
- Parts Used:
- 2159061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Door would pop open. I cleaned gasket made sure nothing in the way of door. Gasket was cracked top and bottom it worked better but the seal was not good.
Did just like the video showed took doors off daughter helped take off doors so easy put door on blanket. My daughter 38 went to town putting it on just watch the corners so easy two days after installation the door seals great. You can do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL B. from ROCHESTER, IN
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Refrigerator was very noisy. Investigation revealed that the condensor fan motor was going bad.
First let me say that the instructional video on your website for this repair was very informative. My son and I watched that before we began the repair. We unplugged the unit first. After removing the back cover, he unplugged the old fan's electrical connection, and then proceeded to remove the fan and bracket from the unit. We then removed the old fan from the bracket, installed the new one and then he reinstalled the new fan and bracket back into the unit. He used the included electric adaptor cable to complete the electrical connection, plugged in the refrigerator briefly to confirm all was well (it was), then replaced the back cover and we were done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from MC CUNE, KS
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
ice maker
My husband is an appliance man and he did the work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Albakurky, NM
- Parts Used:
- 2159061
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
cut old off the door and put new on the door
took door of the refergarator. Then cut old gusket of and clipped the new one on and then put the back. Done!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CHICAGO, IL
- Parts Used:
- 2159060
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Defrost drain clogged with ice
Replaced gaskets on both doors. Followed the online video link that came with emailed receipt. Worked exactly like demonstrated in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from GRANTS PASS, OR
- Parts Used:
- WPW10189703
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
TOO COLD FREEZER, TOO WARM REFRIGERATOR, EVAP FAN FROZEN SOLID
I just followed the directions on the video of my specific model. Make a note of where to locate that video of your model, as there are many other videos of other models that can have different parts located in different areas and it can be time consuming finding the exact video you want again.
Also note that you must make mental or written notes on exactly what direction any parts you remove are facing, this can save huge amounts of time when reassembling.
I was worried that I might need other parts, but decided to do one part replacement at a time since this unit is a spare and no urgency to get it back working again. I found that the evaporator fan was the only thing needed! The fridge works like new again!
Also note that you must make mental or written notes on exactly what direction any parts you remove are facing, this can save huge amounts of time when reassembling.
I was worried that I might need other parts, but decided to do one part replacement at a time since this unit is a spare and no urgency to get it back working again. I found that the evaporator fan was the only thing needed! The fridge works like new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oliver from Madison, AL
- Parts Used:
- 4387535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Cimpressor would not start
Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.
BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.
BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MARYLAND HTS, MO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
freezer (later fridge too) wouldn't stay cold~
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BONITA SPGS, FL
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
install ice maker 2 screws wire harness pluged in done
Was this instruction helpful to you?
Thank you for voting!