4YET20DKXAN00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from Morganton, NC
- Parts Used:
- 1129316
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The original ice-maker had a defective module and the ice-maker kit cost less than a replacement module
Replaced original ice-maker with the ice-maker from the kit. Operational check was good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Marengo, OH
- Parts Used:
- WP4387503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Freezer froze up and water in ice and water in bottom of refrigerator
Had to take everything out and defrost the whole refrigerator dry up and than took back off at bottom and the one covering the Bimetal. The hole was plugged so we took the compressor and blew it and finally got all the ice out before we put on the Bimetal. This is the 4th time we fixed this and I don't know why it won't last longer than 8/9 months. The warrenty is for a year and so far I have gotten 2 refunds thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from newark, DE
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
ice maker would not make ice.The fill tube had seperated and iced up so no water could get to ice maker
Just followed the video that you guys had on line . It was a very easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terri L from Coarsegold, CA
- Parts Used:
- 1129316
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
leaky ice maker/black flakes in ice
The repair was super easy and the part worked like a charm. I love my new ice maker! I had to take out the top freezer shelf just so I could fit my head in the freezer to find one screw, but otherwise all went fine. Ice maker is held on with two top screws and one bottom screw. Loosen the two top screws, remove the bottom screw and lift out the ice maker. It plugs into wires on the inside, back of the freezer so this has to be unplugged. Plug in the wires for the new one, slide it down onto the two top, loose screws, tighten those and screw in the bottom one, replace freezer shelves and you are ready for ice...with no huge iceberg fouling up the ice in your ice cube tray. Simple! The wiring thing worried me when others described it, but it's no harder than plugging in a lamp, really. If I can do it, anybody who can stand on a shorty ladder can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from spring, TX
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice maker water fill tube cracked
hardest part was pulling out the refrigerator. it took about five minutes. parts fit perfectly. only thing to look for is some excess flashing on the end of the tube. easily removed with a pocket knife. simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margo from Baraboo, WI
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf support in freezer
Removed correct part from those provided and slipped it into position. No tools necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Coral Springs, FL
- Parts Used:
- WP4387503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer would frost up then frig temp would rise to un safe tempertures
UN plugged refrigerator,waited 24 hours to let defrost,removed panels,cut out old Bi metal Defrost thermostat,wired in new thermostat,reassembled freezer,plug back in,working great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Pahrump, NV
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water fill tube was broke at the 90° in back of the frige
Water was already off. All I had to do was pull the fridge away from the wall, remove two screws that hold the fill tube onto the back of the frige, then remove the fill tube. Install the new fill tube, reinstall the two screws. Had to cut the water line straight and clean, slip on the new Compression nut and farrell and insert into the new fill tube, tighten-up, good-to-go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Houston, TX
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
fill tube broken at elbow
Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from Crestline, CA
- Parts Used:
- 1123394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
not cooling
R/R part, 3 screws reconnect 3 wires. easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from Ivanhoe, MN
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water tube froze and got bent so it would not fill ice maker properly
Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Virginia Beach, VA
- Parts Used:
- WP2155013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Kick Plate Clip Broke
On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth L from Beaver, WA
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End caps broke leaving shelf unusable
Snapped in new end caps and attahed existing shelf bar. Have done this twice. We tend to stuff too many items on that bottom shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judi from wallowa, OR
- Parts Used:
- WP2196157
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker not making ice
repair went well. Ice maker still not making ice. UGH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Denver, CO
- Parts Used:
- 1129316
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Would not make ice
It started out being a disappointment. I just moved into a new place that needs many repairs so I didnt want to spend too much time on this one. I ordered this part which arrived in just a few days. Not knowing exactly what was broken I just ordered the whole thing. When I opened the box, the first thing I noticed was that one of the parts of the new ice maker had a big crack in it. Not wanting to go through the hassle of boxing it up and going through the return process, I started taking it apart and replacing the worn or broken owned, (exactly why I ordered the entire unit). Nevertheless, I wanted ice so I fixed it with some of the new ones and some of the old ones. By now I've paid too much for the unit but it was my choice not to send it back and I now have ice. It was pretty easy to fix once I had the parts.
Was this instruction helpful to you?
Thank you for voting!