FPE21THW0 Westinghouse Refrigerator - Instructions

Unplug fridge. Removed 2 nuts to get the vent plate off and two more nuts to get the motor mount off. Removed fan blade and then the fan motor. I put the new motor in and put everything back as it was. It was very easy. I had items in the freezer, so I didn't turn the fridge off other than to replace the part. It took about 6 hours for the fridge to reach optional temps because I didn't get to defrost and the fridge had to work it out on it's own. If you don't need the freezer then you should turn the refridgerator off for at least an hour and open the doors so the coils can defrost and any ice blockage between the freezer and fridge portion can melt away as well.

Followed video instruction and completed the replacement. I had to join the wires since the connector was a male plug to a make plug.

Unplugged the fridge. Removed water inlet valve from fridge. Used voltmeter to test for resistance (between 50 and 150 ohms). Didn't pass the test.
My original part was 218720400. I ordered part PS468507 from partselect.com. My original part had a "garden hose" coupling so PS468507 fit the bill.
This part's electrical connection wasn't angled the same way as the original so we had to finagle it.
Hooked the plastic refridgerator supply hose up first.
Then screwed on the copper "garden hose" connection to the valve using channel lock pliers. Was careful not to over tighten.
Then the fun started. The electrical connector wires were a tight fit between the copper tubing and the refridgerator frame. Did I mention that the electrical connetion wasn't angled the same as the original? My daughter got her smaller hands in there and was able to make the connection.
NOTE: Because of the angling issue I was unable to screw the anchor plate to the fridge.
I made sure that the valve did not interfere with the fan.
Turned on the water and checked for leaks.
Plugged the fridge back in and in a couple of hours we had ice cubes. Works like a charm!

Made sure water was going into valve, shut off water to valve, removed it. removed two connections, replaced with new valve, Walla, off & running. Incidentally, rec'd new valve much quicker than I ever expected.

It was very easy. Pulled off the old valve and replaced with the new one and it started making ice right away. There are a couple of issues you need to be aware of that I am watching closely now. The old valve was a 15 watt valve. The one they sent me is a 35 watt valve. It really pressures the water into the ice maker. So much so I am getting a little leaking from the overflow. Its working so well and powering the water in so fast it starts to leak a little due to being to full. When I ordered the part, no where did it show the wattage of the valve so be careful. It works great but will have to keep an eye on it so it does not overflow.

Removed dead water valve. Installed new water valve.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Needed to replace the valve in the back. My first attempt at a fridge repair. New valve went on in a flash and the ice maker is working great.

Emptied freezer, removed fan motor cover (2 screws), removed fan and motor (2 screws), removed old motor from bracket and reassembled with new motor, transferred fan blade from old motor to new), re-installed new fan/motor (2 screws) and reinstalled cover...

The drain pan fit to perfection on our Frigidaire refrigerator model FPE19V3AW1 from 1987(!!!).

change the evaporator fan motor kit working perfect

Followed the instruction video. Removed the old one. Attached the fan blade, ground wire and connected power plug. Reinstalled with 2 screws. Works great.

dismantled the top rear panel of the freezer and found I had the wrong part. Hand started the fan motor and it has been working fine since.

Removed screws that fastened bracket to fridge. Next, I replaced the motor and carefully lined the brackets up so the motor would rotate smoothly. Put the fan blade on the motor and screwed the brackets back on the fridge. Motor kept popping out of alignment while I was screwing the brackets back in but I kept snapping it back in till it stayed.

The repair was straightfoward. The evaporator motor I received from partselect was a different model with different wiring configurations. I cut the wires from the new motor per the instructions I received with the new motor and I did the same with the wires that connect to the fridge. Once I matched the wires and secured them with electrical caps I began to put the evaporator motor to the base and started screwing the screws the way I took them off. Once I connected the wire harness to the back of the freezer and turned it on I noticed a big difference in air flow. I was surprised at how easy it was to fix my refrigirator problem. It's been a few weeks now and the fridge is cold and working like it should. Don't be afraid of this task. it's very easy and will save you a ton of money. Thanks partselect.