GTN217WHE2 Uni Refrigerator - Instructions

removed everything from door, removed screws in gasket around door, laid door face down(insulation side up)applied rtv around edge of gasket and door, waited 10 minutes and started with top screw in middle of top then middle of sides and bottom then installed remaining screws checked levelness of refrigerator, the you are done

change the evaporator fan motor kit working perfect

After reading other posts, I decided to change the defrost thermostat, so I watched the videos, and did that. It got better, but the problem persisted, and the ice was still building up in the freezer section. So I decided that the problem was with the defrost heater. I ordered a new one, that was here under 24hs (using the Fedex ground). I replaced it, measured the old one and saw that it was not passing any current at all (so it was really burnt). Now the fridge is good as new, maintaining the proper temperatures both at Freezer and Fridge sections. Thank you Parts Select ! With $ 70 in parts I was able to get back my appliance working !!!

Unplugged refrigerator. Removed control knob and cover. Unwired control and removed same. Removed plastic tube from old capillary tube and placed on new unit. Installed and wired in new unit, making sure new unit was in the "off" position. Plugged in refrigerator, turned control knob to the first numerical setting, and was rewarded with the startup of the refrigerator compressor. Voila!

open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

Turned off water. Took cardboard backing off lower back of unit. Unscrewed the old adaptor from the water distributor. Unscrewed the water hose connection from the adaptor. Put plumbers tape on new adaptor. Re-connected water hose to new adaptor and re-attached the adaptor to the water distributor. Turned water on, checked for leaks, and tightened adaptor to water distributor until leak stopped (approximately a quarter turn) after hand tightening. Easy, hardest part was pulling out the unit and putting it back in place!

Part Select suggested probable causes and supplied videos of how to make the repair of a 25 yr.old refrigerator along with the specific parts to order. I was about to trash the old refrigerator but after replacing the parts for a total of about $40 and 1 hour of time it works fine now.

The old drain pan had a 1 ½” tall bushing attached to the center of the pan. The new pan did not have this bushing which was great. I had to cut about 1 inch off the bushing to remove the old pan. Also after cutting the bushing I had to screw the bushing off after cutting the old pan from the bushing. I installed new pan onto the ½” of threads that was left on the top of the compressor. Checked repair two days later all was great.

1. Unplug the refrigerator.2. Remove the storage rack and back panel in the freezer. 3. Locate the thermostat. 4. Defrost the freezer coils , i used a hair dryer. 5. Remove the thermostat from the cooling coil and then clip the connecting wires close to the unit. 6. Strip the ends of these wires and connect these wires to the wires of the replacement unit using the supplied wire connectors. 6. Heat seal with a lighter the connections using the water shield sleeves provided and further wrap connections with electrical tape. 7. Reconnect the thermostat to the cooling coil at the location it was removed from. 8. Replace the freezer back panel removed earlierand the storage rack if you have one. 9. Plug the freezer back in. My refrigerator has been working ever since the repair. There are several YouTube videos available that walk you through the diagnoses and repair process. They are very good.

All I had to do was change out motors, and the fam would spin right,and the freezer was alive again. With your older models you may have to re-mount the motor bracket in the back for the fan to clear,due to the fact that the motor sits alittle lower than the old model

This is a top and bottom frige. I unplugged the fridge and I took off the sheld in the freezer and removed the blower fan cover and unplugged the fan to remove the back freezer panel. Be careful when moving the fan. It looks sensitive. I used a hair dryer to melt the frost to get to the screws. Because it was frosted the back panel was hard to take off. Don't force it too much, just keep melting the ice. Once it was off the radiator looking thing was completely frosted and iced over and I couldnt even see the thermostat. I started blowing it with the hair dryer and it started melting. It took an hour to get the ice melted enough to actually see and remove the thermostat. You may want to leave the fridge off for a day. I didnt have a choice because I didnt have anywhere else to place the food. I was using the freezer as the fridge. Thats how cool the freezer was. I cut the wires for the thermostat. Im sure you could check which is positive and which is negative. I just looked at the direction the wires went. This works but it is not guaranteed. Check for ground. Google it if you need to know how. I used the clamp connector things but I didnt have a clamper so I used a plier. It works but I didnt like how it clamped. The little tubing didnt work for me becuase I didnt have a solder gun to warm it up and using a match is not good. You'll burn the wire. Buy electric tape and wrap it around. Dont use regular tape. Go to home depot it costs 99 cents. Make sure all ice is melted. Go over everything with the hairdryer to melt the ice. You dont want it to start freezing and clog up the vents, expsecially the one that goes from the fan to the fridge. Before I put everything back together I changed the defrost timer because I figured its best to change it since you never know. I loosened the two screws but first I took offf the screw holding the timer panel. I changed the defrost timer and connected it back. Then I screwed everything together. Then I screwed in the back freezer panel but not the fan cover so I could see if the fan is working. I plugged in the fridge and the fan didnt work. If you look under the defrost timer panel, the timer has a round part that you can move with a flathead screwdriver. Move it lightly clockwise and the fan will start. I read that the fan goes for 8 hours and then it turns off for a half hour. Seems like a lot of time to be on but its been a week and the fridge and freezer are working real good. This website is good and the aprts are cheaper than Sears.

First I removed the inner door which was easy and used a drill with a hex head driver to undo all of the screws behind the gasket. Trying to fit the new gasket on was a fidely nightmare. It's not too bad to get the sides on but the corners are very difficult. At first I had left the door on the fridge after an hours worth of swearing I took the door right off and laid it flat on a table. When I finally got the gasket all on, with a couple od small tears, I hit it with a heat gun and got most but not all of the wrinkels out. When I put the door back on the fridge it wouldn't close properly - gaps in the gasket. I leaned some weights against the door and it the gasket with the heat gun again. Gradually over 2 days it fit fairley well.

Based on other problems listed I determined I had a bad thermostat, defrost timer, or defrost heater. Since my refrig is over 14 years old I decided to replace all three components since I don't have testing equipment. As a former aircraft mechanic in the Air Force who did a lot of removal and replacement of components I didn't have any problems. Your videos were very helpful and on point. My refrigerator is now working perfectly. My rational for replacing the three components was it was still cheaper than having a refrigeration person to come out and I received your parts the next day. By the way, the defrost timer is located outside in the bottom left front of the refrigerator while the videos suggested that it was inside under the control panel. Thanks!

Replace evap fan motor. Take a close-up picture of the evaporator fan motor installation prior to removing. Take pictures as removing various components.

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.