GTL181BLD0 Uni Refrigerator - Instructions

Followed the instructions that came with replacement ice maker...was very clear and easy to follow and only took 5 minutes. I also watched the video sent via email with my order confirmation which was very well done and easy to follow. The only information that would have helped would have been a note to wait over-night for the ice maker to make ice as I thought I did something wrong when it wasn't making ice right away....waited until morning and had lots of ice. If I knew how straight forward and easy this was, I would have done it a lot sooner.

loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

I found that the fill solenoid for the ice maker was down to a drip when energized. I ordered from this site and replaced. now plenty of water, but the ice maker would just stall and jump teeth. The heater which heats the ice up to free it from the mold was defective. Ordered from this site, and now working great.this sitet has good pricing, and the help illustration is great, and explains the sequence of events. This made it easy to troubleshoot. This refrigerator has not give a problem in over 11 years. The problem is "the ice maker". I have replaced it 6 times.

Followed on line video. Also water supply tube on fridge was full of ice. You can pull it out and run hot water on it to clear.

Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work


Tom Houck
Spokane, WA
Houck Photo
509-723-3418
[email protected]

removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do

The instructions that came with the replacement icemaker were very complete, in particular concerning the small levelling bracket on the bottom of the icemaker, because the old bracket needed to be removed from the old icemaker and transferred to the new one. This part of the installation might not have been obvious, so I was glad to see it clearly outlined in the instructions. The old icemaker was removed by loosening two nuts and detaching the electrical connector, and the new one was installed in its place. Fairly simple, the whole job took about 45 minutes because I work slowly and carefully. A more confident person could probably have the new one installed in 15 minutes. Only drawback: about three to four weeks after installing the new icemaker it has begun making a loud clicking noise on occasions. It is a repetitive (5 second interval) clicking, and only happens for about a minute every few hours and then stops. I am concerned that it might be gears prematurely wearing out and slipping. I guess I'll know in a few weeks if this one stops making ice.********************************************* Update: after about 9 months the new icemaker quit working and will need to be replaced. I removed the front cover from the icemaker and could clearly see that the teeth of one of the plastic gears were worn out and no longer meshing with the opposite gear. The drive gear was just spinning in place and making no contact with the larger gear.

installed new ice maker. Was very esay - the only problem I had was the length of the wire, due to the need to use the adapter, was hard to menauver around so that it didn't contact the bottom of the ice maker. Would be best if it was configured so that you had the right wire connection and didn't have to use the adaptor.

The service man that I hired to fix my Ice maker removed the broken one. This is how I saw how easy it was to install. When the new one arrived all I had to do was plug it in then tighten 2 screws with the right size nut driver. This was the hardest part of the install havng the right tool for the job. Now I have Ice!

Replaced defrost timer & thermostat.

LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!

Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE

Turned off water, unplugged refrigerator, Removed defective unit with support bracket. Installed support bracket, adjusted flow screw per instructions, plugged in wiring with adapter, hung on screws, tighened screws, secured excess wiring harness (making sure it did not hang below icemaker per instuctions), turned on water, plugged in refrigerator. Comment it took a few hours to start making ice, air in line? After a couple of days seems to be working fine.

The repair took only 5 minutes. I removed the ice bin, which just slides out, then loosened 2 screws at the back-top of the ice maker. I then unplugged the broken ice maker, removed it, put in the new one, re-tightened the screws and plugged it in. It was making ice within an hour.