Models > TRT17CRAW0

TRT17CRAW0 Tappan Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for TRT17CRAW0

Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
If your freezer will not defrost, or your fridge and freezer are too warm, there may be an issue with the defrost timer. This device helps to melt ice that builds up on the evaporator coils. It does t...
In Stock
Order within the next 8 hrs and your part ships today!
$19.73
Clear, 120 Volt, 40 Watt.
In Stock
Order within the next 8 hrs and your part ships today!
This is a white cut-to-fit door shelf retainer bar.
In Stock
Order within the next 8 hrs and your part ships today!
This is the door shelf end cap for your refrigerator. It connects to the refrigerator door and keeps the door bar in place. Your refrigerator will have two shelf end caps, one for the right side and o...
No Longer Available
This white end cap is a little over two inches long. It is used for the right side of either the refrigerator of the freezer door shelf.
No Longer Available
This part is attached to the compressor. It helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
In Stock
Order within the next 8 hrs and your part ships today!
This limiter thermostat cuts out when the temperature inside your refrigerator reaches 55 degrees Fahrenheit and kicks back in when the internal temperature drops to 20 degrees Fahrenheit.
In Stock
Order within the next 8 hrs and your part ships today!
This motor runs the evaporator fan in your refrigerator. It is mounted on the center hub and has three lead wires terminals. This motor rotates in a clockwise fashion. Its shaft has a diameter of 1/8" and is 1-1/4" long.
In Stock
Order within the next 8 hrs and your part ships today!
This is the door shelf end cap for your refrigerator. It connects to the refrigerator door and keeps the door bar in place. Your refrigerator will have two shelf end caps, one for the right side and o...
In Stock
Order within the next 8 hrs and your part ships today!
This is the door shelf end cap for your refrigerator. It connects to the refrigerator door and keeps the door bar in place. Your refrigerator will have two shelf end caps, one for the right side and o...
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for TRT17CRAW0

Viewing 17 of 17
Fridge too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Freezer not defrosting
Fixed by these parts
Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Light not working
Fixed by these parts
Fixing Fixing
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Fridge runs too long
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Fridge too cold
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Won’t start
Fixed by these parts
Fixing Fixing
How to fix it
Freezer too cold
Fixed by these parts
Fixing Fixing
How to fix it
Door Sweating
Fixed by these parts
Fixing Fixing
How to fix it
Frost buildup
Fixed by these parts
Fixing Fixing
How to fix it
Doesn’t stop running
Fixed by these parts
Fixing
How to fix it
Clicking sound
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Stephen from Warrington, PA
Parts Used:
5303917954, 215846602
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Fridge got warm and freezer coils were frosted
Fridge is a side by side. The freezer is pretty narrow for a guy with wide shoulders.

Pulled plug.

Had to remove bottom drawers then used nut driver to remove screws closest to back wall in drawer runners. Once the back screws were removed the runners could be swung up or down out of way so back cover could be re moved.

Once back cover was removed thermostat was located attached to top pipe going into coil using a spring clamp.

Cut the wires just outside the crimp connectors going into thermostat. Released the spring clamp buy squeezing botton together.

Removed old badly corroded thermostat.

I wish I had attached the crimp connectors to the new thermostat wires before mounting it. Reaching way in the back, while turning shoulders verticly and trying to get the wire connectors set from both sides was awkward and uncomfortable...The biggest PIA of the whole task.

Once connected I let the fridge (thermostat) cool for 10 min. Turned the dial defrost timer to get it into defrost mode. Stupidly touched the heating element to see if it was getting warm...it was very hot.

Coils steamed...every looked like it was working. Unplugged, put back cover back on and retattached drawer mounts.

Plugged back in and everying is working great!
337 of 401 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jordan from Maumee, OH
Parts Used:
5308000010, 5300158289
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Noisy fan
1. Removed the 7 nuts using the nut driver from the freezer back panel inside the freezer.
2. Remove the back panel. The evaporator motor and fan are located above the coils.
3. Unplug the wiring harness.
4. Remove the two gold mounting screws holding the motor and fan in place.
5. Remove the motor and fan including th e brackets.
6. Install the new motor and fan onto the mounting bracket.
6a. Attach the green ground to the mounting bracket.
7. Screw the two gold screws back into the freezer.
8. Attach the new wiring harness. Note, the old harness had a mounting hole/space for it to connect to the wiring harness of the freezer. The new motor's harness was not long enough for this, so it is connected freely to the freezer harness.
9. Use the hair dryer to melt any ice that may have formed on the coils and hole where the fan goes.
10. Turn the freezer on to see if the fan turns on.
11. Reinstall the back panel.
All done!
153 of 180 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Melvin from Semmes, AL
Parts Used:
216008900
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Clicking sound then within a minute clicking again, not cooling.
UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it r attles like a baby rattler then it's most likely the problem. Replace wires into the new relay and plug back into the compressor.
79 of 93 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!