RF267ADRSXAA Samsung Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deryl from KINGWOOD, TX
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door would not close properly
Spent a dollar 1.97 on the spring.7.00 on shipping and fixed it in less than 5 minutes.Fantastic
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CADILLAC, MI
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken spring on french door
Placed lower spring leg in hole first. Manipulated upper spring leg into upper hole with needle nose pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST JORDAN, UT
- Parts Used:
- DA97-07365G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker leaking water into ice bin.
Took out Philip’s screw. Applied heat from hand hair dryer for one minute. Unplugged wire plug. Pushed ice maker lever to release and gently pulled forward.Removed old ice maker and replaced with a new maker.
Plugged in wire harness and replaced wire cover.
Plugged in wire harness and replaced wire cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORTHWOOD, NH
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Just follow instructions. Easy
Held spring with needle nose pliers and slipped into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Libor from Danbury, CT
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door spring
replacing broken french door spring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnathan from Nashville, TN
- Parts Used:
- DA97-07365G
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker no longer made ice.
Prepare the area
Open the refrigerator door(s). Remove the ice bucket/bin by lifting it up and pulling it out (it usually slides forward after a slight lift). Set it aside. Empty any loose ice.
Remove the ice maker cover / upper panel (if present)
There is often a plastic cover or shroud over or in front of the ice maker. Gently pull or pry it off using a flathead screwdriver on the release tabs. Some models have screws holding this cover. Note the orientation for reassembly.
Disconnect the wiring harness
Locate the electrical connector (usually a 12-pin plug) on the side or back of the ice maker.
Press the release tab on the connector and gently pull it apart. Do not yank the wires. Tuck the harness aside safely.
Remove the mounting screws
There are typically 2 screws (Phillips) securing the ice maker to the refrigerator wall or bracket — one on the side/top and possibly another. Support the ice maker with one hand while removing the screws so it doesn’t drop.
Remove the old ice maker
Carefully tilt and pull the unit forward/out. It may have tabs or hooks that need to be released. Wiggle gently if stuck. Avoid forcing it to prevent breaking plastic parts or damaging the fill tube.
Install the new ice maker (DA97-07365G)
Position the new assembly in the same orientation. Align any tabs, hooks, or slots with the mounting bracket.
Reinstall the 2 mounting screws snugly (do not overtighten).
Reconnect the wiring harness firmly until it clicks.
Reassemble the cover/panel
Snap or screw the cover back into place.
Reinstall the ice bucket
Slide the ice bin back in until it seats properly.
Power on and test
Plug the refrigerator back in.
The ice maker may take time to cool down and begin a cycle (several hours).
Press the Test/Reset button on the ice maker (small button on the side or front of the unit) to run a test cycle if available. You should hear the motor and eventually a fill.
Check the control panel on the door — ensure Ice Maker is turned On (not Ice Off).
Monitor for the first batch of ice (can take 6–24 hours depending on temperature and usage).
Open the refrigerator door(s). Remove the ice bucket/bin by lifting it up and pulling it out (it usually slides forward after a slight lift). Set it aside. Empty any loose ice.
Remove the ice maker cover / upper panel (if present)
There is often a plastic cover or shroud over or in front of the ice maker. Gently pull or pry it off using a flathead screwdriver on the release tabs. Some models have screws holding this cover. Note the orientation for reassembly.
Disconnect the wiring harness
Locate the electrical connector (usually a 12-pin plug) on the side or back of the ice maker.
Press the release tab on the connector and gently pull it apart. Do not yank the wires. Tuck the harness aside safely.
Remove the mounting screws
There are typically 2 screws (Phillips) securing the ice maker to the refrigerator wall or bracket — one on the side/top and possibly another. Support the ice maker with one hand while removing the screws so it doesn’t drop.
Remove the old ice maker
Carefully tilt and pull the unit forward/out. It may have tabs or hooks that need to be released. Wiggle gently if stuck. Avoid forcing it to prevent breaking plastic parts or damaging the fill tube.
Install the new ice maker (DA97-07365G)
Position the new assembly in the same orientation. Align any tabs, hooks, or slots with the mounting bracket.
Reinstall the 2 mounting screws snugly (do not overtighten).
Reconnect the wiring harness firmly until it clicks.
Reassemble the cover/panel
Snap or screw the cover back into place.
Reinstall the ice bucket
Slide the ice bin back in until it seats properly.
Power on and test
Plug the refrigerator back in.
The ice maker may take time to cool down and begin a cycle (several hours).
Press the Test/Reset button on the ice maker (small button on the side or front of the unit) to run a test cycle if available. You should hear the motor and eventually a fill.
Check the control panel on the door — ensure Ice Maker is turned On (not Ice Off).
Monitor for the first batch of ice (can take 6–24 hours depending on temperature and usage).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from BUENA PARK, CA
- Parts Used:
- DA63-03773A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Bulb bracket broke
The website offered next day delivery on the 2 parts I needed. It was $30 dollars for next day but I wanted it fixed so I chose it. After a few days I revived no parts. I checked the website and saw the 2 parts were on back order, however they took my payment along with the $30 for next day delivery. Obviously I never got it next, or ever, so I cancelled the order. At least I got my money back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from RALEIGH, NC
- Parts Used:
- DA32-00006R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator was too cold - down to 18 degrees Fahrenheit.
Removed shelves. Removed back cover. Removed old sensor. Installed new sensor. Replaced back cover. Replaced shelves. Works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from BUTTE, MT
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door
Replaced the spring on my French door refrigerator
Was super easy
Was super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from ARLINGTON, MA
- Parts Used:
- DA97-07276E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
french door mullion busted
Piece of pie! Took of the screw caps, the screws, disconnected the wire switch and reversed direction with the new one. 10 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharol from Culdesac, ID
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Brokjen spring
Lifted out the broken part and replaced with new spring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RYAN from RIVERBANK, CA
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
french spring broke
after receiving spring installed spring in seconds. Thanks partselect.com Ryan Cappell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Bensalem, PA
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
French spring broke.
pushed new spring in.
Was this instruction helpful to you?
Thank you for voting!