RF28HMELBSR (AA-0006) Samsung Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from GULFPORT, MS
- Parts Used:
- DA32-10104N
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Evaporator frozen (refrigrator section) and allowing top section to lose cooling
This is the Samsung French door refrigerator style that so many people have complained about freezing up and not cooling the top section. I first changed out the defrost thermostat and this did not correct the problem. I done a quick resistance check on the temp sensor that's mounted on the evaporator itself. The resistance would change when holding an ice cube on the sensor so I just assumed it was ok. PLEASE TAKE NOTE: When performing a resistance check on this sensor, make sure your readings match the Samsung temp/resistance chart in their literature. My sensor was way off calibration and was causing the freeze up. Its working as designed now and DW is happy again. Learn from my mistake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from BAKERSFIELD, CA
- Parts Used:
- DA97-12625A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
CLOSING MECHANISM BROKE IN TWO.
OPENED THE LEFT SIDE REFRIGERATOR DOOR WHERE THE DEFECTIVE MECHANISM WAS. GOT UP ON THE FIRST STEP OF THE STEP STOOL,REMOVED THE PHILLIPS HEAD RETAINING SCREW FROM THE BROKEN PART.PUT THE NEW CLOSING MECHANISM IN PLACE AND RE-INSTALLED THE PHILLIPS HEAD SCREW. STEPPED DOWN FROM THE STEP STOOL AND SHUT THE REFRIGERATOR DOOR.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger Holmgren c/o Lazarus from LAKEWOOD, CO
- Parts Used:
- DA82-02161E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer door was dented. Found a new one at PartSelect.
1) Remove items from freezer.
2) Remove/lift out top slider drawer, and the in door slot tray.
3) Remove lower, large plastic tub/drawer bottom.
4) Remove 6 of the 8 phillips head screws that hold the sliders to the drawer front.
5) Remove while holding up the drawer front with foot, or other spacer to hold up the drawer front when removing the last 2 screws.
6) Pull rubber gasket out of the original drawer front, and press it into the new drawer front.
7) loosen the allen screw from the bottom right side of the handle.
8) slide the handle to the right to remove it from the old door.
9) Slide the handle in place onto the new door, and tighten the allen screw on the bottom right.
10) Place the new drawer front onto the slides. (There are 2 dowel type knobs that locate the drawer front correctly.)
11) Start 1 screw into each slider, making sure that the dowels line up with the holes in the sliders.
12) Install the remaining 6 screws holding the sliders to the drawer front. 13) replace the bottom tub, the slide drawer, and long slot tray.
You're done, other than reloading your frozen items back in the freezer.
2) Remove/lift out top slider drawer, and the in door slot tray.
3) Remove lower, large plastic tub/drawer bottom.
4) Remove 6 of the 8 phillips head screws that hold the sliders to the drawer front.
5) Remove while holding up the drawer front with foot, or other spacer to hold up the drawer front when removing the last 2 screws.
6) Pull rubber gasket out of the original drawer front, and press it into the new drawer front.
7) loosen the allen screw from the bottom right side of the handle.
8) slide the handle to the right to remove it from the old door.
9) Slide the handle in place onto the new door, and tighten the allen screw on the bottom right.
10) Place the new drawer front onto the slides. (There are 2 dowel type knobs that locate the drawer front correctly.)
11) Start 1 screw into each slider, making sure that the dowels line up with the holes in the sliders.
12) Install the remaining 6 screws holding the sliders to the drawer front. 13) replace the bottom tub, the slide drawer, and long slot tray.
You're done, other than reloading your frozen items back in the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from MADISON, AL
- Parts Used:
- DA97-12625A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Part broke
Took out the screw, removed the broken part, put new part on, put retaining screw back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from HENRICO, VA
- Parts Used:
- DA67-01650A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
A broken siphon break elbow
Partselect made the repair process incredibly easy by linking a how-to video that explained exactly what to do. Without the video, I was trying to take the whole washer apart, but the video noted a convenient opening that provided easy access.
This is my second experience with Partselect, and I am definitely a fan. How you can maintain a stockpile of parts for so many appliances (as well as providing installation guidance for at least some items) is remarkable. Thanks.
This is my second experience with Partselect, and I am definitely a fan. How you can maintain a stockpile of parts for so many appliances (as well as providing installation guidance for at least some items) is remarkable. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from FORT WORTH, TX
- Parts Used:
- DA97-14474C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic housing for ice maker cracked preventing the internal mechanism from moving/emptying ice cubes
Since the ice maker was no longer able to empty ice and the problem was a large crack in the plastic housing right near where the internal screw connects to maker (which we were unable to fix with something simple like tape) we simply had to swap out the whole ice maker. It was just the process of pulling the old one out and sliding the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from BAKERS MILLS, NY
- Parts Used:
- DA61-03734A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
We misplaced the mounting screws for our handles while moving.
It was easy! I just used an alan wrench to losen the side bolt, then slid the handle into the new mounting screws that I had hand-screwed and then tightened it all up.
Was this instruction helpful to you?
Thank you for voting!