RFG293HAPN/XAA Samsung Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- curtis from BYRON CENTER, MI
- Parts Used:
- DA81-01346A, DA81-01345B
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
This company failed to get me the parts i needed. Wasted my time and caused a loss.
Called someone else. Got the parts elsewhere.
Got the fridge back online 3 week longer than it should.
got charged for the part then failed to send it.
then finally allowed they didn't have the part in stock.
Got the fridge back online 3 week longer than it should.
got charged for the part then failed to send it.
then finally allowed they didn't have the part in stock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellie from Buckley, WA
- Parts Used:
- DA81-01346A, DA81-01345B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The french door would spring close or open.
I removed the old spring along with the sleeve and inserted the new one in its place. used a small screw driver to remove the sleeve and inserted the sleeve side in first. took 5 minutes..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Dahlonega, GA
- Parts Used:
- DA81-01346A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower hinge for spring
After purchasing the spring I realized the hinge was the culprit. It has the retainer for the spring as part of it, a small plastic piece that broke off cause the spring to get lost. The hinge replacement was a little more in depth but the video on the hinge is very good and on point.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deryl from KINGWOOD, TX
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door would not close properly
Spent a dollar 1.97 on the spring.7.00 on shipping and fixed it in less than 5 minutes.Fantastic
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CADILLAC, MI
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken spring on french door
Placed lower spring leg in hole first. Manipulated upper spring leg into upper hole with needle nose pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from MACUNGIE, PA
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken mullion spring on left door
Placed one end of the new spring in left hole and used the needle nose pliers to insert the other end of the spring in the right hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from FEDERAL WAY, WA
- Parts Used:
- DA97-06419C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked Door Bin
Slide the old door bin out. Put the new door bin in. That easy! Fits perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORTHWOOD, NH
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Just follow instructions. Easy
Held spring with needle nose pliers and slipped into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Libor from Danbury, CT
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door spring
replacing broken french door spring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PALM DESERT, CA
- Parts Used:
- DA61-07540A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door handle pulled away from door due to broken plastic strip.
Received package, cut open. Removed broken handle. Unscrewed broken support. Support slid right out. Took off end piece. Added end pieces to each new support. Slid new support into place. Re-set screw. Re-attached handle. Couldn’t believe it was so easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Chapel Hill, NC
- Parts Used:
- DA67-02056A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right side of freezer door handle broke
This is the older model of the Samsung refrigerator, so there is **no Allen screw underneath the handle** to remove it. That was a change made on newer models.
To replace the broken freezer handle cap:
1. **Remove the gray top cover.** Slide the gray cover forward, then lift it up and off.
2. **Remove the two Phillips screws** underneath the cover.
3. **Remove the front tabs.** Gently pry the front of the tabs forward. Using needle-nose pliers, carefully pull the tabs out.
4. **Remove the broken cap.** Once the tabs are removed, the broken cap can be taken off.
5. **Remove the handle from the old cap.** In my case, the handle had broken away from the old cap. There are two Phillips screws securing the handle to the cap. Remove those screws and separate the handle from the old cap.
6. **Reuse the silver hinge pin.** Before discarding the old cap, remove the silver rod/hinge pin by sliding it out. You will reuse this pin in the new cap. If necessary, apply a small amount of light lubricant to help it slide out and back in.
7. **Attach the handle to the new cap.** Use the two Phillips screws to attach your existing freezer handle to the new cap.
8. **Install the new cap and handle.** Position the new cap and handle assembly on the freezer door. This part is a little fiddly, so be patient and make sure everything is properly aligned before tightening anything.
9. **Reinstall the two tabs.** Put the tabs back into position and secure them with the two Phillips screws.
10. **Replace the gray cover.** Snap the gray cover back over the new cap.
That's it. The key difference with this older Samsung model is that **you do not remove the handle with an Allen screw**. The handle is secured to the cap with two Phillips screws, and the silver hinge pin from the original cap is reused in the replacement cap.
To replace the broken freezer handle cap:
1. **Remove the gray top cover.** Slide the gray cover forward, then lift it up and off.
2. **Remove the two Phillips screws** underneath the cover.
3. **Remove the front tabs.** Gently pry the front of the tabs forward. Using needle-nose pliers, carefully pull the tabs out.
4. **Remove the broken cap.** Once the tabs are removed, the broken cap can be taken off.
5. **Remove the handle from the old cap.** In my case, the handle had broken away from the old cap. There are two Phillips screws securing the handle to the cap. Remove those screws and separate the handle from the old cap.
6. **Reuse the silver hinge pin.** Before discarding the old cap, remove the silver rod/hinge pin by sliding it out. You will reuse this pin in the new cap. If necessary, apply a small amount of light lubricant to help it slide out and back in.
7. **Attach the handle to the new cap.** Use the two Phillips screws to attach your existing freezer handle to the new cap.
8. **Install the new cap and handle.** Position the new cap and handle assembly on the freezer door. This part is a little fiddly, so be patient and make sure everything is properly aligned before tightening anything.
9. **Reinstall the two tabs.** Put the tabs back into position and secure them with the two Phillips screws.
10. **Replace the gray cover.** Snap the gray cover back over the new cap.
That's it. The key difference with this older Samsung model is that **you do not remove the handle with an Allen screw**. The handle is secured to the cap with two Phillips screws, and the silver hinge pin from the original cap is reused in the replacement cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from SAUTEE, GA
- Parts Used:
- DA67-02057A, DA67-02056A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Installed caps on broken lower handle
Unscrewed broken caps and installed new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from ANN ARBOR, MI
- Parts Used:
- DA97-06419C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken fridge door bin
The description at the website was excellent so I was confident I was ordering the correct replacement bin. And it slid right in with no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from RALEIGH, NC
- Parts Used:
- DA32-00006R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator was too cold - down to 18 degrees Fahrenheit.
Removed shelves. Removed back cover. Removed old sensor. Installed new sensor. Replaced back cover. Replaced shelves. Works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from FLORISSANT, MO
- Parts Used:
- DA67-02057A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer handle had broken free from the left side of the door.
On both sides of the door there is a pop off cover that houses the broken mechanism. I popped off the cover and exposed the screws the attached the handle to the opening mechanism. removing those screws I removed the handle from the freezer door. I replaced the broken plastic piece on the handle . Reattached the repaired handle assembly to the door with the 4 screws. Reinstalled the cover.
Was this instruction helpful to you?
Thank you for voting!