Models > RT21M6215SG

RT21M6215SG Samsung Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Models for RT21M6215SG

Diagrams for RT21M6215SG

Viewing 5 of 0
Keep searches simple, eg. "belt" or "pump".
The ice maker shut-off arm stops ice production when the ice bin is full.
In Stock
Order now and your part arrives by Jul 18
On Order
This is a 40W/120V ice maker assembly for your refrigerator. Ice maker assemblies are designed to continuously make ice cubes by supplying water through its valve, freezing it, and then ejecting the c...
In Stock
Order now and your part arrives by Jul 18
The Samsung Defrost Sensor (DA32-10105R) is a genuine part designed specifically for Samsung refrigerators. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is...
In Stock
Order now and your part arrives by Jul 18
In Stock
Order now and your part arrives by Jul 18
$90.58
In Stock
Order now and your part arrives by Jul 18
In Stock
Order now and your part arrives by Jul 18
The door bin attaches to the inside of the refrigerator door and typically holds jars and bottles.
In Stock
Order now and your part arrives by Jul 18
In Stock
Order now and your part arrives by Jul 18
This manufacturer-approved screw is for refrigerators, including Kenmore refrigerator model. Avoid cross-threading refrigerator screw during installation.
In Stock
Order now and your part arrives by Jul 18
In Stock
Order now and your part arrives by Jul 18
In Stock
Order now and your part arrives by Jul 18

Common Problems and Symptoms for RT21M6215SG

Viewing 4 of 4
Ice maker not making ice
Fixed by these parts
Fixing Fixing
How to fix it
Ice maker dispenses too much ice
Fixed by these parts
Fixing
How to fix it
Fridge too warm
Fixed by these parts
Fixing
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from WILMINGTON, DE
Parts Used:
DA32-10105R
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers
Ice Build up behind refrigerator internal panel
I performed the repair to my own refrigerator, after watching multiple YouTube videos. I installed a secondary heater for the defrost coils and replaced the defrost sensor. The defrost sensor was actually bad. Today, 1/27/2024 I rechecked the fix from last week. All seems to be good so far.

If I get any build up of any ice on t he bottom tray of the recessed panel where the drain port is located. I suspect I will also need a new Defrost Heater as well. For now the refrigerator is operating as expected. There is a small amount of ice build up as of today.

Also, I had recently replaced the drain tubes, added a longer heater element part to fit the drain hole, and cleaned the fins in the back of the refrigerator. Thank you.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from Belle Fourche, SD
Parts Used:
DA32-10105R
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Fridge side no longer cooled, freezer still workekd fine.
A couple of blogs said the freezer defrost sensor should be replaced, so I ordered one. Did not fix it. I did, however find a service manual online and one of the blog sites and it showed me how to remove the inside duct work. I discovered the fan the recirculates the air across the evaporator coil was not working. Ordered a new fan mo tor and installed it, fridge works perfectly now.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Streator, IL
Parts Used:
DA97-07603B
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set, Wrench set
The ice maker was overflowing and freezing over
I watched several repair videos and decided I could do this because I have been doing mechanical work for over fifty years.The videos convinced me it needed replaced it is a 2009 model I bought new. I ordered the new part from parts select it came in 3 or 4 days.The hardest part was removing the freezer door and reinstalling when I was do ne.That wasn’t complicated just awkward.Removing the ice maker was simple and replacing it with the new one was easy.There was a protective plate on the front of the old one that wouldn’t fit on the new one.So I left it off.So far it has been working very well.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!