RT14BKXKQ05 Roper Refrigerator - Instructions

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

First I watched the video on your website, it was quite helpful. It showed me the location of the part to be replaced. Then I used the nut driver to remove a couple of screws, and slowly pulled the cover off . Once I pulled the cover down I could see the part that needed replacing, it had a couple of phillips head screws holding it in place, I removed those screws and unplugged the defrost timer, taking note of the color of the wires. Then I took the new defrost timer and attached the loose wire to the correct terminal according to the directions(this is where the color of your wires comes in), then I plugged in the new defrost timer and replaced the screws. I then reattached the cover making sure not to pinch any of the wires, and replaced the screws. It was so easy I was sure I did something wrong and it wouldn't work, but I plugged the refrigerator back in and let it sit for about 20 minutes and then when I checked it was running cool. I'm 55 years old and never had the nerve to try anything like this before but since my husband passed away I've had to try things myself or replace a lot of appliances. If I can do it anyone can.

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

Removed/replaced ice maker and valve per enclosed instructions. If you can service your own lawn mower this R&R should be easy for you.

I unplugged the refrigerator(for safety). Using a 1/4" nut driver I removed 1 screw holding ice tray rack. I then removed the 2 screws holding the lower shroud inside the freezer section. I then removed 1 screw holding cover plate where ice maker would be and disconnected the ground wire from the back panel. I then removed the 2 screws holding the back panel in place. This allowed me to removed back panel from from inside the freezer. I removed the fan blades from evaporator motor by pulling straight away from motor. I was then able to disconnect the power wires and the ground wire from evaporator motor. Using the 1/4" nut driver I removed the 2 screws holding the front motor bracket and removed the evaporator motor from its bracket housing. Using the an electrical cord that i had fashioned with two female spade connectors on each lead of the wire, i connected these to the motor and plugged the male end of the electrical cord into a standard 110v outlet to verify that the motor was in fact the defective component. The motor did not operate so I replaced the evaporator motor with a new motor and put everything back in reverse order. The refrigerator is running like a champ and keeping the refrigerator contents a cool 42 degrees. Thanks PartSelect.com

Followed a youtube diagnostic video on a whirlpool fridge with the same configuration. After determining that the problem was the thermostat I ordered the part from parstselect. I was pleasantly surprised by both the fair shipping price and the 2 day arrival. Replacement was as simple. Cut the old wires, wire nut the new ones. Wire colors are the same on my old unit and the replacement, but these generally aren't polarized anyways.

We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH

Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.

I'm not sure you really want to know. We had to use one of the two refrigerator shelves we purchased, which was too big to fit in the freezer. It had to be completely modified in order to accomplish this. We therefore cut the shelf in half lengthwise. To do this, it was necessary to determine the tools needed, then to gather them and finally use them. It took a good amount of foresight and perseverance, but the job was completed, works beautifully and is very helpful. We wondered why a freezer shelf was not available or if it was, why it was not clearly identified in the parts list.

Exactly how the part select video described it. Threw a little curve ball figuring out which timer setting to set it to. But the instructions provided with defrost timer walked me right through it. No problem. After installing part nothing happened for about ten minutes, which had me second guessing each and every step. Then, like magic, cold air began blowing. What a relief. Thanks so much, love this site. Refrigerator works like new!

I cut the plugs off and bought male and female wire conectors and crimped them on the wires and pluged them together.