RT14VKXDW00 Roper Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lucy from Portland, OR
- Parts Used:
- WP2201061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
bent door shelf bars
I was able to replace the the shelf bars with no difficulty after finding the right parts on PartSelect. The easy to view measuring menu helped me get the right size for the fit I needed. You always worry when you don't have the item in front of you but they make it easy to gauge. I will use them again. I replaced three bars that had been driving me crazy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Radcliff, KY
- Parts Used:
- 4387913
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refrigerator would not get cold
Took a little while to figure out that I needed a flat tip screwdriver to lift up on the top of the plastic housing in order to tip it forward and remove it. After that I used pliers to remove the wires from the old parts and place them on the new. Removing and replacing the parts was performed by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Brooklyn, NY
- Parts Used:
- 4387478
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Protective cover for bulb had melted
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eliseo from Pleasanton, TX
- Parts Used:
- 482731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
no problems at at all
removed rear wall panel took off old fan motor disconnected motor. Installed new grommets re-installed motor inserted new fan. Didn't have to trim fan re-connected wires and rear panel and reconnected power. no problems...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Hilliard, OH
- Parts Used:
- 482731
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Evaporator motor squeal.
After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sierra Vista, AZ
- Parts Used:
- 482731
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
rReally Noisy Fan
1. Unplug Refrigerator 2. Remove inside back freezer panel. (4 Screws) 3. Remove Duct Cover (3 Screws). 4. Cut electrical connections to fan. 5. Remove Old Fan motor (2 hex screws. 6. Install ground wire (was not one there previously). 7. Put slide-on electrical connectors on remaining 2 motor wires. (Were not any on original unit.) 8. Replace Fan Motor (Don't forget the rubber vibration pads) 9. Reconnect electrical wires. 10. Press on plastic fan blade. 11. Plug in refrigerator to test install. It works. 12 Unplug refrigerator and replace ducting and back panel to freezer. Plug it back in. Voila, Quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Ledyard, CT
- Parts Used:
- 482731
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Repalce evaporator fan
The evaporator fan is located in the freezer behind the back wall. If you have the ice maker remove it first then remove the screws on the top of the panel. You will notice the side brackets for the top shelf will make it hard to remve the panal but by slitly binding the center the panal came right out. The fan is held in a bracke tha comes right out. The wire unplu right from the fan so do not try to unplg the seal plug to the left side. Swap the fan with the new one useing the new rubber monts re-connect the wires and reasymble. Put the bottom of the back panal in first then work each side in past the shelf bracket binding the center slightly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Pearland, TX
- Parts Used:
- 2188445A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replace door gasket
Needed to replace a really old Refrigerator Door Gasket and was having difficulty locating a door gasket for this unit. We didn't even know the age of the unit, but found the model number of the refrigerator which no one really lists on websites because it's so old. Customer service found the Model we had, we ordered and it was received at our home the next day.Price was good and the shipping chg was very reasonable. Very pleased and will definately order from them again! Thanks!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph D. from Culpeper, VA
- Parts Used:
- W10373956
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bottom door handle broke
After learning the top and bottom part separate from the handle itself, all I needed to do was to take off the bottom part which was broken and replace the broken part with the new part , that was in a kit, I purchase from Whirlpool.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Cincinnati, OH
- Parts Used:
- 482731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy fan
Unplug the refrigerator. Remove the rear shelf supports by lifting them straight up. No tools required. Remove the screws holding the rear cover of the freezer. Use a nut driver to remove the 4 screws holding the fan housing. Unplug the wiring harness, then remove the fan and install the new one. Remount the housing, plug in the harness replace the rear cover, install the shelf supports and plug in the refrigerator. It was 30 minutes start to finish, which includes the time to gather the tools, unload and reload the freezer, and putting the tolls away!
Was this instruction helpful to you?
Thank you for voting!
My refrigerator was warm and my freezer was frozen over. There was no air circulation.
First i unplugged the power. I changed the thermostat first. With a nut driver i removed the 14 screws and slid off the back panel inside the freezer compartment. I removed the old thermostat by unclipping it and disconnected the two wires it came with. I clipped in the new thermostat and reconnected the two wires. I slid the panel back on and put the screws back on. This took less than 10 minutes. It is so easy. My seven year old son can do this. I then proceeded to change the defrost timer. I have a built in so i removed the wood panel on top of the fridge to expose the timer. The timer was a bit hard to get to because its inside a metal housing on built ins. I removed as many screws on the front part of the housing until i was able to squeeze in my hand. I removed the two screws that attach it to the box and then unplugged it and slid it out. It was really stuck so i used a screw driver to loosen it from the plug. I plugged in the new on and screwed everything back in. It took about 20 minutes. If its not a built in refrigerator, it will take 5 minutes. I plugged the refrigerator back in and everything is perfectly cool and cold. It is really simple and cheap to change these parts. Don't get suckered into expensive repair bills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxine from Henderson, NV
- Parts Used:
- 482731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The fan in the freezer was squealing
Took the old fan out and put the new fan in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Arlington, MA
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Arvada, CO
- Parts Used:
- 482731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
noisey circulating fan in the freezer
Emptied the freezer. Removed the back panel. (six screws)Removed the fan cover.(4 screws) Unplugged the power. Unplugged three wires from the motor. (hot-neutral-ground)Removed the fan. (2 screws) Installed the new fan and centered for clearance. Reversed the prior instructions.
Was this instruction helpful to you?
Thank you for voting!
Cold air not flowing between freezer and refrigerator sections
Replaced air baffle between sections - part number PS321610. This part is quick connect with no wiring required. Start by turning off appliance using thermostat dial on freezer side. Remove cover for air baffle in upper left rear corner of refrigerator compartment. Remove wire harness cover between air baffle assembly and front upper control panel of refrigerator. Remove screw covers from under upper front control panel in refrigerator. May need to pry them off with a butter knife or thin screwdriver. Pull off thermostat dial. Unscrew mounting screws to remove upper front control panel cover. Pull out old air baffle assembly but do not unplug wire harness. Slide new air baffle assembly into position. Following the old part's wire harness, run wire harness for new part to point where old wire harness connects. Match up the old and new wire harness connections, unplug the old wire harness and plug in the new wire harness making sure the wires for the old and new correspond. Remove the old part and wire harness and secure the new part wire harness in the wire harness track. Reinstall the front control panel cover and thermostat dial and the screw hole covers. Reinstall the wire harness cover. Reinstall the baffle door cover. Turn the appliance on. You have now saved yourself a few hundred dollars in labor costs!
Was this instruction helpful to you?
Thank you for voting!