RT18ECRHW00 Roper Refrigerator - Instructions

NO DIRECTIONS CAME WITH GASKET! Project failure as gasket tore on a corner. For the price of this gasket, I was DISAPPOINTED. Door is being held shut with a childproof strap.

First I removed the old hardware from the door and reused the screws that I had to replace the handle. very simple swap. handle was not shipped with screws so hope you have yours.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

First took all frozen food out and than undid the screws that held back on--than cut the wires that held the piece and replaced it but also found that the plug was frozen so we thawed that out, that is why it took longer. Used air compressor to blow air and it broke it free and than we finished and put the food back after it got cold. So far it is working find and to beat all we received our part the next day so my husband could fix it that weekend--Thank you for the quick respond-
Patricia in Marengo Ohio

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Repair man that looked at it said it was the thermostat and that he would order the part. Waited two weeks with no word, so I ordered the part on line, got it the next day and installed it. The only hard part of the installation was getting to the three screws (located vertically in top of refrigerator section) to remove them. Simple three wire clip on changed unit. Total time took about 5 minutes. Refrigerator started cooling when plugged back in. Unfortunately, cooling again stopped within a day, so the original problem was more extensive than just the thermostat (so much for the service call diagnosis). Thoroughly pleased with part ordering, would do it again.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Unplug pwr cord ..then chk voltage on refrigerator...go inside refrigerator to upper unit where light is and lower unit dwn bye removing the screw then look for thermostat it's right inside ..remove to 3 wires then install new thermostat the same way....plug unit in to power rotate thermostat cooling setting and listen for compressor to tune on. If all goes well the refrigerator should cycle. ....if not change out control board. Good luck and have fun.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Original handle had broken, and super glue wasn't holding any longer. It's just three screws, two up top and one on the bottom that hold the handle on. The fridge and thus the handle comes in three colors (white, biscuit ,and black) I had to email customer service to find out that white is part no PS330447. I got an absurdly fast reply to my question given it was a Saturday afternoon, so that made it easy.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

This job was extremely easy, snap on.

Easy