RS25AGXNQ01 Roper Refrigerator - Instructions

I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.

My husband and I followed the instructional video on how to replace the "direct drive drum". We took note of how everything looked prior to dismantling the ice bin. We made sure we had the proper tools and a large flat surface to work on and started taking out the screws. Replaced the new drive drum part and put it all back together. The whole process took approximately 30 minutes and the ice crusher works great now. I'm a happy camper!!

Ordered a new shelf. Removed the old one and installed the new one. Wife is happy. :-)

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

I watched the YouTube video on your website, performed the task as depicted in the video, and had absolutely no difficulty. The fellow in the video must be stronger than I am, so I used a pliers to twist out the old, and twist in the new. And while turning off the ice maker first was a good hint, he forgot to tell me not to turn the old filter upside down after removal because it is pretty much filled with water. I kind of think I'm pretty handy, but your site is really, really good for the average homeowner.

I watched the ice maker installation video and I installed the new ice maker with no problem and was done in less the 30 min. with everything. The ice maker is working great. thank you Fred

Door cams were worn out. Removed food from door. Removed top hinge cover and hinge. Lifted door off lower hinge pin and placed door on a table. Removed old door cam and installed new one. Replaced closing cam on lower hinge. Set door back on lower hinge and closed door (magnetic strips hold the door in place). Reinstalled top hinge and replaced cover.

I receved the new ice maker and the only problem I had was getting the old ice maker plug disconected from the frig.

remove items from old bin remove bin replace new bin after removing was remove .

I pulled the refrigerator away from the wall, unplugged the electrical cord, and turned off the water going to the refrigerator. I then removed the cover on the bottom rear of the refrigerator by removing 7 or 8 small screws. Luckily the new and old valves were exactly the same except for some color coding. There were 2 screws to remove that attached the valve to the body of the fridge. There were 3 plastic tubes that connected to the valve and 2 wiring harnesses that plugged in. Before removing them, make sure to note which tubes and wires went where. The 3 tubes on the old valve were the push in type, just like the new one. I could not pull 2 of them out like the instructions said. I had to pry them out with a screw driver. In doing so I warped about 1 inch on the end of each tube which I then cut off with a razor blade. The electrical connections pulled out easily. I then pushed each tube back into the new valve which was very easy and pushed the electrical connections in. I attached the valve to the fridge with the 2 screws, turned the water on, plugged in the electrical cord, and checked for leaks. I put the back cover on and was back in business. It took me about 40 minutes but when I was younger could have done in in half the time.

Watched the video link from the part order and the step by step instructions were as easy as the repair man showed. This is an easy do it yourself job that will fix the problem I describe with the unit. Ahhh a working freezer making and keeping ice once again.

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions