RT18DKXJW00 Roper Refrigerator - Instructions

Attached Three screws, Done.
Luckily I kept the old screws. If the screws & screw cover had been included that would have been an added bonus. However not the case.

Part Select made it so easy, they told me to download the video I did and I had it fixed within 15 minutes. Part Select is awesome, they helped me diagnose it and told me what part I needed. I will definitely use them again, and I highly recommend them.

Inserted scraper behind gasket breaking it free from door, permitting a hand hold. While putting tension on gasket, slid scraper around door gently removing old gasket. Replaced gasket starting at top gradually working around door. No need to remove door.

The first part I changed was the defrost timer but it did
not solve the problem, I replaced the bi-metal defrost sensor
and I have the same problem.

I can defrost by turning the clock manually and heater works.



























problem.

Just installed the 4 screws

Removed the old gasket and ran the hard edged lip into the opening behind the door liner. Concerned that the gasket does not seem to be attaching itself to the door well. First put it on the side of the refigerator and it would not adhere enough to support itself. While it closes it just doesn't seem to attach with the magnets in the gasket. These magnetic strips have a weak magnet side and a strong magnet side. I wonder if they put the wrong side facing the door when they assembled it. Counter this with a new gasket for an upright freezer which was twice the length and attached itself firmly to the side wall of the freezer and did not slide down.

I followed the instructions on the video you provided with my order. Removed the freezer door and used the putty knife to loosen the old gasket and installed the new one. I'm a 77 year old female and if I can do it, so can you.

Got on floor, pulled broken parts off front of refrigerator. Clipped in new grille. Looks great!

The Defrost Timer is located in Refrigerator section (not the freezer) where your temperture guages are. Move panel and replace the non working Defrost Timer with the new one. It took my husband about 30-40 mins to fix. This was about 2 weeks ago and my Freezer and Refrigerator are working like new. I bought this Kenmore Reftigerator brand new in 1996 and I lost the manuel to it. Thanks to my daughter who found the Defrost Timer on the Internet, I thought I was going to have to buy a new one. This was real easy to fix. The instructions that came with the part was easy to understand and very self explanatory. It also had very good diagrams to follow.

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

I just replaced my defrost thermostat after using the place-in-ice-water method, and I think it may not have been necessary. My timeline: my fridge was not getting cold enough. I realized it the day before going on a trip. I vacuumed the (very dusty) coils at the bottom, and the next morning the fridge seemed colder, but I thought I should order parts just in case. I ordered a heater and a thermostat. The fridge seemed to be operating normally when I returned from my trip, but I had the parts, so I thought I'd go ahead and dismantle the freezer and test the existing parts. My intention was to return both parts if the old ones passed the tests. I opened up the back of the freezer and there was no ice on the fins. I thought, great, the existing heater works! I cut out the thermostat, placed it in ice water, and didn't get continuity. So I decided to go ahead and put in the new thermostat. Because I'm not experienced with using a multimeter, I thought I'd test the new thermostat to see how the test should work. To my surprise, the new thermostat also failed the test! Stumped, I thought I might as well install the new thermostat, since I had opened the package and couldn't return it.
Further internet research suggests the place-in-ice-water method of testing is not adequate. One YouTube video by Parts Dr says to place the part in a working freezer. I froze my old thermostat and tested it; still no continuity. This thermostat may not be typical, though. The video discussed the temperature ratings on thermostats. The temperature rating on both (old and new) thermostats is L8.9-16.7C. That converts to 48-63 degrees fahrenheit, which obviously are not freezing temperatures. I'm not convinced I needed a new thermostat, but I trusted the videos I consulted earlier.
I cleaned the fridge thoroughly, so at least now I have a nice clean fridge to show for my efforts.

Check for Video if any, watch 2X. The parts may look different (but not this time) Unplug.Defrost timer-dropped the control panel in the frig. the defrost timer sits right in the middle switch it out.Turn the timer to be set on the on cycle. Wasn't sure if the Bimetal thermostat was bad too so for a little over $20. I changed that too.- in the freezer- remove the metal panel and fan cover. its clipped on to the element tubing on the right. cut the wire. Splice the wire to connect the new one then cover with wire nuts. replace cover, plug in. use frig thermometer to verify temperature.

followed directions

Took everything out of the old one, lined the new one with cloth and put everything back in.

When we got the part, we read the instructions, which were easy and very clear step by step. Taking the old part off took most of the time, it was attached a little differently than was described in the video and the instructions for the part. Once we detached that, the replacement part went in very easily and quickly. It took a short while for the cycle to start, we were actually a little worried that it wasn't going to work. Then it started cycling. After the first day the freezer had started icing up, we took a blow dryer and melted it and waited. It hasn't started freezing up again. The refrigerator is keeping the proper temperature and the freezer is also working properly, it's been a week. We seem to be obsessed with going out and checking to see if it's working but I think it's a success. Doing this ourselves only cost $26.00. A huge savings if we had hired someone else to repair it for us. We will definitely choose this option with any other appliance that needs repair. It was easy and simple to find the correct part thanks to the website. And the video tutorial was very informative and helpful.