MTX14EYTGRWH RCA Refrigerator - Instructions

we took off the old one and replaced it.

I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before ordering. Otherwise, the entire process from order to finish took about 3 days.

got on part select web site and found other customers that had same problem and on their site they had comments from them to fix problem. I then took off back panel on frig where compressor is by removing 6 screws and found the relay attached to the compressor then pressing down on holding spring removed 2 wire alligator clips and it was bad ordered one from part select put the new one on an frig was fixed. entire fix took about 30 minutes from isolating problem to fixing it. thank you part select

Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.

First, I love that fact that my new fridge piece came in the mail in 2 days! I didn't order it as a rush, but I'm so glad it came so quickly! The installation could not have been easier! It took me longer to clear off my broken vegetable pan cover than it did to pop the new one in. My overall experience was amazing and super easy! I'll be back to PartSelect should I need I need to replace anything else in the future.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

new cover slipped right in place, however, the way the new one is designed, the hump in the front rubs the bottom of the door. you have to make sure you push the door shut or it will remain open .

I took out the old shelf and popped in the new one. Took 1 minute or less. The delivery was in 2 days! Amazing experience! My refrigerator feels brand new.

The part just snapped into the shelf bar. Extremely easy to fix. Since you show the part in a grid I was able to tell, by holding my old piece up to the screen, that the new part would be the correct size. We have rentals and are always needing parts for appliances. Impossible to find locally.
Also the part came so quickly it was almost as good as buying it here in town. Thanks. Donna Bingham

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.