MSX22GLC RCA Refrigerator - Instructions

I had to defrost freezer first becasue it was heavily iced up. Then I found that one of the heater elements was "open". I removed both of the old heater elements and installed the replacement parts.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

remove the 8 screws 2 for each rail
installed the new rails
slid in the meat drawer and glass
slid in the vegetable drawer and glass
presto - like new fridge !

First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

First i removed the lower cover below doors . Then placed a 4x4 under the door to be fixed to keep it in place. Removed screws from hinge support on unit to remove cam Removed outside screw on door and loosened other to allow other cam to be removed . Always buy two cams if one is broken the other cant be in very good shape .The door will work like new with two .

Removed the top hinge cover held by one screw. Removed the top hinge held by two screws and them lifted the door up and off the bottom hinge. Laid the door on the floor and replaced the cam piece from the kit on the bottome of the door. That required removing one screw and losening another. Removed the lower hinge (two screws) and replaced it with the new one in the kit. The lower hinge includes the other cam piece. Lifted the door onto the lower hinge and then replaced the top hinge and cover.

Read the how to's AFTER ordering the part. 2 things....1) I wish I had read the comments first and 2) it was much easier than the comments led me to believe.

Had I read the comments first, I would have known to order BOTH the upper and lower cam....though there not a problem with the operation of the door. It would just have been a tad better if I had both. I'm not wanting to have to pay shipping for an additional part when the door works satisfactorily as it is.

As to the comments on how to do it....I took none of them. I (instead) removed the top hinge, and lifted to door off. I did have to have assistance to get the hole in the door aligned with the post, but that was rather easily done.

Would I do it again.....in a heart beat. I feel that I've save on the repair man making a call at the house, and experience has had me charged $60-$100 for virtually the same amount of service. My cost...shipping and all was under $20.00

I removed the door from the bottom hinge assembly by removing the top hinge assembly.
1. Installed the cam to the bottom of the door.
2. Installed hinge and bottom pin & cam to the refrigerator.
3. Reinstalled door and adjusted front roller height to make door close better.

I removed all items from the door to make it lighter. Then, with the door closed, I lifted the door and placed a 2x4 plus a paint stirrer shim under the door to hold it off the bottom hinge. I used a small socket set to remove the two hex head screws from the existing hinge assembly, which I then removed from the door. Using the same socket set and socket I removed the two screws from the bottom of the door that were holding on the upper piece of the door closing cam. I took care to note the orientation and position of two shims and cover that were with the cam. I used the old shims with the new upper cam piece that came with the hinge assembly and attached them to the door with the original two screws. Finally I inserted the new hinge assembly and mounted it to the refrigerator frame. I finished the job by lifting the door and removing the 2x4 and shim. The new parts worked perfectly.

The drawer slide rail involved removing the Convertable Meat Pan drawer and lifting off the top glass plate. The slide rail was removed by unscrewing two phillips screws. The two screws were used to attach the new drawer slide rail then I replaced the top glass plate and drawer. Very easy assembly operation.

Remove glass shelf, then remove drawer. Remove 2 screws holding old broken rail in place and replace using the same screws. Replace the drawer and glass shelf.

After reading the stories here, I purchased one door closing cam. After getting into the problem area, I realized I needed 2 cam, so I put the door back together and ordered another cam. If you have this problem, buy 2 cams.

First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think about offering them as a set?
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.

I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.