MTX21ELB RCA Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kevin from Morris, IL
- Parts Used:
- WR55X24065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Compressor not coming on
Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Macungie, PA
- Parts Used:
- WR24X446
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
gasket cracking at least 8 years old
Excellent instructions from your video. Replaced gasket once without removing door quite harder to do. Placed gasket in sun to warm it up, didn't have to heat it in hot water. Much easier once doors are removed and replaced gasket on large table or bench. Thanks for the video and your prompt delivery of part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Summerville, SC
- Parts Used:
- WR24X446
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Fresh door gasket leaking.
Followed the PartsSelect how-to video to the letter., using clothes dryer option to soften the gasket before installation. Installing the new gasket a little tedious, but not difficult. Video was dead on as to method and tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theodore from salisbury, NC
- Parts Used:
- WR60X30349, WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bad fan motor
take fan out,put new in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NORTH PALM BEACH, FL
- Parts Used:
- WR24X445
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Freezer door gasket replaced
Both PartSelect and GE advisors told me to remove/loosen screws holding gasket to the door. This model has no screws. After pulling to old gasket from a corner (very difficult) I found that it is held in place by pressing it into a channel running around the door. Very difficult to line up the proper parts and very difficult to slide/adjust it into place. When finally installed, one corner of the gasket protruded so that the door was not flush and actually kept the door from closing. I tried to push/pull it into place. No good. Finally I tried to hammer the gasket back to make it flush. No good, as it evidently crushed the magnets providing the necessary holding power and produced gaps. I finally had to get foam window stripping plus heavy duty magnets to pull door to frame. Result: door closes OK but some moisture collects around door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Rock Hill, SC
- Parts Used:
- WR2X7674
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door shelp end caps broken
clip out, clip in, easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Williamsburg, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new light socket
Pulled out old socket.pushed in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Orcas, WA
- Parts Used:
- WR24X446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Refrigerator door gasket was coming apart.
I watched the video, supplied on the website, two times and followed the procedure. The repair was very easy and a pleasant experience. Lay the new gasket out flat for a couple of days in the sun prior to installation and remove the door and lay it flat for the installation of the gasket. Remove old gasket and clean track and surrounding area thoroughly. Line up new gasket over track and at each corner and press into track, starting in center of one side, and work your way to each corner - repeat on each of the remaining three sides. Use a wet sponge to slide along the top of gasket while pressing same into track on the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Seatac, WA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from Elk Grove, CA
- Parts Used:
- WR24X446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator gasket was worn and old.
Manually snapped the plastic gasket into the slots of the refrigerator. The part fit perfectly after a slight adjustment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Leavenworth, KS
- Parts Used:
- WR2X9391
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light would not stay on
First I flipped breaker to off position for refigerator, Pulled down on socket and broke it free. Then took needle nose piars to pull wire and plug out from hole, so I could conect to new light socket then snaped it in place . Hardest part was getting wire and plug out of hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!