MTX18EPNRAD RCA Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kristina from Southbury, CT
- Parts Used:
- WR24X450
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacing the refrigerator gasket
Start at the inside top corner and slowly work across the top, pushing with thumbs so that you feel it fitting into the groove. Go inch by inch. No speeding on this one. The gasket was so well packed that there were no folds or kinks, so no heating was necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRYAN from SOLON SPRINGS, WI
- Parts Used:
- WR24X450
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The door gasket was coming apart
I just let the gasket sit on a flat surface for a couple of days. I didn't immerse it in hot water as the directions stated. It went on fairly easy. Just took a bit of patience. The fact that it was packaged nicely without it being jammed into a tight bundle probably was a big factor in the ease of installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from FRANKLIN SQ, NY
- Parts Used:
- WR23X10725
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light not working
I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Federal Way, AL
- Parts Used:
- WR23X10725
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Difficulty in removing the old switch
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Crown Point, IN
- Parts Used:
- WR23X10725
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refrigerator light wouldn't come on.
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Coto de Caza, CA
- Parts Used:
- WR23X10725
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Interior Light did not go on due to faulty switch
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from RNCHO CORDOVA, CA
- Parts Used:
- WR07X26748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Does not start , trips breaker
I pried the relay from compressor with small screwdriver, cut and replaced burnt wire going to relay,pushed new relay on compressor and wires unfortunately it did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from OZARK, AR
- Parts Used:
- WR9X483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
freezer compartment worked fine but very little cooling going to refrigerator section.
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The replacement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Winchester, MA
- Parts Used:
- WR24X450
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Gasket had deteriorated at bottom.
I removed the old gasket and snapped the new one into the grooves. No tools were required.
PartSelect provided excellent service. It was a GE manufactured part. GE no longer stocked this part.
PartSelect is a terrific appliance repair parts vendor.
PartSelect provided excellent service. It was a GE manufactured part. GE no longer stocked this part.
PartSelect is a terrific appliance repair parts vendor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from Coto de Caza, CA
- Parts Used:
- WR23X10725
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
switchlight on my refrigerator was not working
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from carmel, NY
- Parts Used:
- WR60X123
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not cooling and freezer freezing up
I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Tacoma, WA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light wouldn't come out of socket
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marnie from Denver, CO
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
a fan blade broken causing it to make a loud noise
we took off the old one and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CLIFTON, NJ
- Parts Used:
- WR60X187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Fan would not turn when the refrigerator came on all the time. Would physically have to turn the fan blades.
Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from BERLIN, MD
- Parts Used:
- WR07X26748
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
refrigerator would not get cold
got on part select web site and found other customers that had same problem and on their site they had comments from them to fix problem. I then took off back panel on frig where compressor is by removing 6 screws and found the relay attached to the compressor then pressing down on holding spring removed 2 wire alligator clips and it was bad ordered one from part select put the new one on an frig was fixed. entire fix took about 30 minutes from isolating problem to fixing it. thank you part select
Was this instruction helpful to you?
Thank you for voting!