GC2227DEDW Maytag Refrigerator - Instructions

1. Removed ice bin.
2. Removed vertical panel next to ice bin by sliding two top supports off of support posts and pulling the panel out and up.
3. Removed screw on left side holding ice enclosure in place.
4. Pull ice enclosure out about six inches and tip back end down exposing electrical connector.
5. Detach the electrical connector by pressing the release tabs on the top and bottom of the connector.
6. Removed ice eclosure by pulling it up and out.
7. Detached motor (4 screws) and relay (4 screws) from plastic enclosure. Make sure to keep track of screw positions since they are not all the same size. Use same positions to reassemble.
8. Hold shaft of motor with needle nose vise grips and remove the "U" shaped end piece by turning it clockwise. A sharp rap with a screwdriver handle breaks it loose. Pay attention to the orientation of the washer under the "U" shaped piece (the raised inner edge next to the shaft goes against the "U" shaped piece.
9. Attach the motor and relay to the new ice enclosure paying attention to the screw position.
10. Put the washer on the motor shaft (raised side up) and screw on "U" shaped piece (counter-clockwise).
11. The rest of the installation is a reversal of the removal process.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

Popped the top cover of the handle to expose two screws at the top of the replacement handle. Removed those two screws to loosen the handle and expose the third screw at the bottom of the handle. Replaced the handle with the same 3 screws. Total time 10 minuets

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

first i remove the two screws like the guy said on your web site. then i pulled the cover off with a upward motion revealing three more screws witch i removed. I then removed the dispencer. unpluged the wires and removed the switch and pad and replaced with new parts.I reinstalled the wires then the unit, installed the screws and cover.Checked for proper operation.Then enjoyed that cold beer! Thanks to your wed site and repair info. I saved at least 100 buck to the repair man. Thanks Partselect.com

I read many reviews on how to change the seal/gasket, and decided that as I was the only one around to do the job, it would be easier to take the fridge door off and then lay it flat. remember to take the handle off as well. Then it was a case of taking each screw of, there are many to remove. While this job was being completed, I placed the new gasket in hot water from the tap to soften the gasket as it came in a box folded. Once all the screws were removed , then it was a case of fitting on the new gasket starting from top and working my way around. finally placing all the screws back, but not too tight. Then I placed the door back and also placed a flash light in the fridge to see if any light was coming out. The door opened and closed without any problems and the seal did not have any gaps. finally with door on the fridge, I tightened the screws-only hand tight. Job completed. This may sound obvious, but any way, dont forget to disconnect the fridge from the electrical supply, otherwise you risk burning out the motor, with all the extra work the fridge has to do, while you are doing the replacement.

First I removed the spill tray, and removed the two screws on the bottom of the dispenser. I was then able to remove the front of the dispenser, which revealed 3 more screws. After removing those screws, the entire assembly lifts out. I removed the old pad, put the replacement pad on, replaced all the screws and the tray, and was done! It took about 10 minutes, start to finish. I saved at least $75 on the repair by doing it myself, and the part only took 3 days to arrive. Best of all, the water and ice dispenser works like new! Thanks, PartSelect!

This was a very simpler repair to an annoying problem. First I removed the decorative cover on the top hinge pin of the door which was held on with one screw. I then removed the 3 screws of the top hinge pin with a socket, held the door in place with my hand and took off the top pin. Next, I simply lifted the refrigerator door off the bottom worn out hinge.
removed the old door hinge bracket and bottom lower hinge pin that had worn, placed the new bottom hinge pin in the bracket. Finally, on the bottom of the refrigerator I replaced the natural door closer held on by one screw. Lifted the door back onto the new bottom hinge pin, held the door in place and installed the top hinge pin, put the cover back on and the refrigerator is closing like it was new again.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems.

I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed