MTB2448DRB Maytag Refrigerator - Instructions

First turned off the water and unplugged the refrigerator and then removed the old ice maker by first removing the side cover plate and then next removed the ice level detector. Remove the screws that hold the ice maker in place and rotating it somewhat soas to gain access to the wires and then unplugged them. Next I had to modify the way the water comes into the new icemaker by adapting a CPVC street ell to fit into the hole on the side and then hook up the water supply. Installation is just the reverse of removal.

removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away

Calrod element shorted, arc left burn marks in freezer, harness was burned. Replaced icemaker and wiring harness. Shut off arm [wire frame element] replaced, new version of the wire shut off arm does NOT require the old plastic ice level sensor to be installed on the new shut off arm.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Spoke to Rep.Advised that several parts might be involved. Replaced 3 recommended parts and frig works like brand new. Saved hundreds of dollars in repairman costs.l. Plus $1000.00 for cost of new frig. If you can walk and chew gum at the same time? Easy fix. Very skilled Rep's!! Excellent service!! Great prices!! Highly recommend!!

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness

Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on

ALL FIXED!

installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.

I slid the meat tray out of the broken rails and after cleaning it I used a flat head screw driver to pry gently the plastic rails slightly away from the metal tray to unlock the broken plastic rails and slid them forward to free them off the metal tray.Replacement was very easy sliding the new plastic rails back on the metal tray until they locked into place then screwed the plastic wheels on to the new rails and replaced the repaired tray back into place. Thank you Part Select for your service and help.

Terry R. from Oklahoma City

Replaced ice ice maker using
All of the instructions on the website.
Very easy. A couple of the screws I had
To feel for because I couldn't gety big head
In the freezer far enough to see them.
Very simple and only took about 15 minutes.

Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.

Removed the old icemaker and installed the new one. The first one we ordered lasted about 4 weeks and pooped out. Parts Select was very nice and gracefully sent another in two days time. This one has been installed and is working fine...Hope it stays that way.

Thanks...Ron Norwood

This was a very easy repair. Of course start by unplugging the power cord. Take out the lower freezer drawer. Unplug the wiring harness from the ice maker at the rear of the freezer. Undo 3 screws with a 1/4" nut driver. The ice maker will come right out. You don't have to undo any water connections, the feed tube just slides into a guide in the ice maker. Once the ice maker is out, unplug the harness from the old one and snap it into the new one. Same with the cover. Reassemble in reserse order. Plug the power cord back in and wait a couple of hours for the familiar sounds of ice cubes falling into the tray.

, to remove the inlet tube holder/guide gadget thingee: (1) remove the three Phlipscrews from the motor end of the housing. (2) pull the housing straight off the end. (3) remove two Philips screws in deep holes that hold the ice tray onto the motor housing. (4) this frees the ice tray assembly, which you have to pull out, freeing the rotating blades, from which (5) you slide the sxle out of the middle of the inlet-tube thingee, so (6) you can then remove the inlet gadget from the ice tray.

You then reverse these instructions to reassemble with the correct inlet gadget. The tricky part is the front cover that hides the ice-tray from view. That cover has a couple of ears that have to fit into mating holes in the motor housing before you replace the two deep-hole Philips screws that hold the tighten the ice-tray assembly back onto the motor housing.

So it's too bad they don't see the ice-maker assembly with all the knock-outs inplace, so you can knock out the one you want. Other than that, it would have been no more trouble than other people have reported in working in the tight space inside the freezer compartment.

Replaced ice maker but now water valve wont work