GT2127PVCW Maytag Refrigerator - Instructions

We followed de video that made it very clear to us. Thank you! It's been working great since...

Had to take everything out and defrost the whole refrigerator dry up and than took back off at bottom and the one covering the Bimetal. The hole was plugged so we took the compressor and blew it and finally got all the ice out before we put on the Bimetal. This is the 4th time we fixed this and I don't know why it won't last longer than 8/9 months. The warrenty is for a year and so far I have gotten 2 refunds thank you!

The kickplate grille is a plastic part which has two metal clips attached to it. The old plastic frame had broken free of the metal clips and fallen off the refrigerator. Step One: Removed the two old clips by pulling them out of the refrigerator frame. Did it with finger pressure. 2. Pressed the new part which has clips attached to it into the holes in which the old clips had been placed. Voila, the repair was finished.

Pulled up part select video on u-tube. Followed instructions on dissambly of top freezer and found condensor freezing up blocking air from refrigerator. Checked timer to make sure it was good. Next checked continuity on heater to make sure it was good. Last checked bi-metal thermostat for continuity while cold. Found Bi-metal part to be defective (also rubber in top of was popped up which is a sign of a bad part). Simply ordered new part from Part Select, received in 2 days and replaced Bi-metal and melted ice with hair dryer and reassembled freezer. While waiting on part you can still use refrigerator by melting ice so air can get to refrigerator. I put a towel in bottom of freezer to catch water. Greg W. in Ga.

removed old mount with allen wrench replaced with new mount

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Replacement would have been easy except there was so much ice built up inside the door. Should have just turned it off for 48 hours to let ice melt. Instead completely disassembled door to remove ice.

After watching the video it was a snap. Defrosting the freezer took the longest time. I used a hair dryer to melt the ice. Once the freezer compartment was clear of ice the removal and installation were a step by step procedure which the video showed in detail. It's been about a week since I installed the bimetal defrost thermostat and it seems to be working like new. Sure glad I researched this problem on the internet instead of calling a very expensive repairman! Thanks partselect. Com!!!

UN plugged refrigerator,waited 24 hours to let defrost,removed panels,cut out old Bi metal Defrost thermostat,wired in new thermostat,reassembled freezer,plug back in,working great

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

followed the video instruction from part select web site

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.