GC2229GEHW Maytag Refrigerator - Instructions

Part selects cataglog for parts selection was very easy to use and the online service and delivery was great.
When I got the part, it was not apparent on how to remove the auger so that I could insert the new connector. There were about about 8 visible screws, with star drive heads that I fortunately had a screwdriver that fit, and I could not tell if I had to remove all of them or only a couple.
I ended up removing all, but still could not separate the dispenser portion which held the front of the auger from the back of the ice bin. I finally figured out that the dispenser door trip lever had to be disconnected and I almost lost it when I removed the metal clip that attached it to the outside of the ice bin when the spring loaded lever tried to unwind. I managed to hold it in place, separate the dispenser holding the auger from the rest of the ice bin and replace the connector. I them got the pieces back in place and was able to refasten the spring loaded lever and then replace the screws.
If the spring loaded lever had unloaded, it would have been tricky to try to replicate the amount of turns (load) on the spring tension.

It was easy breezy!! I felt like an empowered woman that I did it myself. I simply removed the old shelf supports with a screwdrive and inserted a screw thru the new supports and screwed them in.

1/4 turn of old filter. it popped out. Inserted new filter, 1/4 turn and it clicked in. Piece of cake. I'm a freakin' genius.

Unscrewed old filter and screwed in new filter.

googled for answer, deduced relay/switch problem. googled again for parts, found partselect.com, ordered part. 2 days later & $70 lighter, my 8yr old Maytag was working again! Parts were good fit, instructions were decent enough. Not for inexperienced tinkerer though.

I removed 3 screws that held face panel in place and unplugged and removed face panel. I removed one screw holding limit switch in place, unplugged switch and removed actuator pad and switch. Installed new limit switch and actuator pad. Repaced front panel and dispensor - now works like a new one.

The driver that turns the screw broke off the ice enclosure. I removed the side panel, removed one screw underneath the enclosure, unclipped the wire harness and removed the entire enclosure.

I did one unnecessary step and removed the magnet from the housing. Better to remove the entire housing, then transfer the motor and magnet to the new housing.

I noticed that others had problems unscrewing the drive unit (which you need to do to transfer it to the new housing.) I simply held the center hub with a pair of pliers, and gave the drive one tap with a hammer. Like the other reviews, note that it unscrews opposite way.

Reassembly was quicker and easier; just undo everything you did to get the housing out of the freezer.

First removed the old water filter and replaced it with the filter bypass. Very simple and no tools needed

Removed the four screws around the shaft. Removed the support nut on the underside of the enclosure. Pulled the enclosure out of the freezer. Removed the "blade" from the drive shaft - This was somewhat difficult as others have described. Needle-nose vice grips are almost a requirement or you'll never get it off. (Turn clockwise to remove it, as the threads are reversed). Attached the motor to the new enclosure with the four screws. Replaced the enclosure and screwed in the support nut on the underside. The difficulty in this whole process by far is removing the blade from the shaft. It takes a lot of force. At one point I almost gave up thinking that it was manufactured or pressed on. It finally came loose, and then the reinstall was no problem. My suggestion would be to let the motor and parts heat up to room temperature for a bit. It may help. A little spray of WD-40 may help as well.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

This was the easiest project of the Holidays. Literally saw the part was broken, went on-line and ordered the part and in a few days it arived at my door. Removed a few screws, unplugged the electrical connector and transfered the motor to the new part.

Saved me a few hundred dollars the repairman would have charged!

THANKS

First I compared the old parts and new parts to see if I had ordered the right thing then I inserted the new stop into the door. Since the stop has a lip that needs to fit into the slot I the door, I used a hammer to push the part up so it would lock into the hole. Very Simple