AS229FWWGB Maytag Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Williamsburg, VA
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace water filter
Unscrewed old filter and screwed in new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from North Las Vegas, NV
- Parts Used:
- 61003791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
New Water System In Home, Needed Filter Bypass
First removed the old water filter and replaced it with the filter bypass. Very simple and no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Las Vegas, NV
- Parts Used:
- WP628356
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water Fill Cup Broke
The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aliki from Miami, FL
- Parts Used:
- WP628356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill cup broke.
Very easy to order from parts select. Took seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Menifee, CA
- Parts Used:
- WP61003336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Old plastic ring was damaged due to leaking icemaker causing door to open when ice dispensed.
No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hank from Alpharetta, GA
- Parts Used:
- 61003791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter costs ridiculously high!!!
Replaced filter with by-pass plug. For some reason though, ice maker does no longer functions, although there is flow out of the cold water tap. Is the design of the bypass plug such that, when installed, it impedes flow to the ice-maker?
Thanks
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennie from ASHEVILLE, NC
- Parts Used:
- W11618980
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The lightbulb burned out
Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- veso from Macomb, MI
- Parts Used:
- 67001454
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Grinding metal sound when opening refrigerator door.
Removed screws from upper hinge. Removed washer from door stopper on bottom hinge. Lifted door off lower hinge. Replaced bushing.
Took about 15 minutes and cost less than $12. Service call alone was going to be $70.
Took about 15 minutes and cost less than $12. Service call alone was going to be $70.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Highland Village, TX
- Parts Used:
- 61005520
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice dipsenser was malfunctioning
Viewed the repair video. Removed covering. Replaced limit switch, control board, and solenoid. Very easy repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Fayetteville, GA
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace the water filter for the refrigerator
I watched your online video on how to take out the old filter, and then to replace it with the new filter. It was as easy as on the video. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GOSHEN, IN
- Parts Used:
- W10156818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wife used vacuum cleaner and busted blade off fan
Instructions were great five minutes to remove and replace fan....Thank You............ saved big money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Newport News, VA
- Parts Used:
- 61005520
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The ice door wouldn't open.
I followed the video of your repair man. Made it very easy.Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from beverly hills, MI
- Parts Used:
- WP67001964, WP61005886, 61004388
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice dispenser door won't close
It was only the door but it wouldn't come out without disassembly of the entire dispensing section; this meant removing the front section and disconnecting 2 pcs from 3 wire harnesses...much more involved than I thought. The spring and strike were fine, but when I reassembled the unit it didn't work. The key was the mechanical connection with the solenoid. It is not obvious and directions would have been helpful. BTW unlike me, flip the power off. I got a good shock from the accuator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Brentwood, TN
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
It was time to change the water filter.
All work was done by hand. I removed the cover plate, unscrewed the existing water filter and screwed in the new one. I returned the cover plate to its original position and bled the air out of the line by running the water dispenser for a few minutes. It could no have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Whiting, IN
- Parts Used:
- 61005520
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
ice despencer not running
repair&parts instalation was easy but troubleshutting difficult.
Was this instruction helpful to you?
Thank you for voting!