GC2228GEHW Maytag Refrigerator - Instructions

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.

first i remove the two screws like the guy said on your web site. then i pulled the cover off with a upward motion revealing three more screws witch i removed. I then removed the dispencer. unpluged the wires and removed the switch and pad and replaced with new parts.I reinstalled the wires then the unit, installed the screws and cover.Checked for proper operation.Then enjoyed that cold beer! Thanks to your wed site and repair info. I saved at least 100 buck to the repair man. Thanks Partselect.com

I read many reviews on how to change the seal/gasket, and decided that as I was the only one around to do the job, it would be easier to take the fridge door off and then lay it flat. remember to take the handle off as well. Then it was a case of taking each screw of, there are many to remove. While this job was being completed, I placed the new gasket in hot water from the tap to soften the gasket as it came in a box folded. Once all the screws were removed , then it was a case of fitting on the new gasket starting from top and working my way around. finally placing all the screws back, but not too tight. Then I placed the door back and also placed a flash light in the fridge to see if any light was coming out. The door opened and closed without any problems and the seal did not have any gaps. finally with door on the fridge, I tightened the screws-only hand tight. Job completed. This may sound obvious, but any way, dont forget to disconnect the fridge from the electrical supply, otherwise you risk burning out the motor, with all the extra work the fridge has to do, while you are doing the replacement.

I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!

I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems.

First I removed the spill tray, and removed the two screws on the bottom of the dispenser. I was then able to remove the front of the dispenser, which revealed 3 more screws. After removing those screws, the entire assembly lifts out. I removed the old pad, put the replacement pad on, replaced all the screws and the tray, and was done! It took about 10 minutes, start to finish. I saved at least $75 on the repair by doing it myself, and the part only took 3 days to arrive. Best of all, the water and ice dispenser works like new! Thanks, PartSelect!

I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

Very easy to remove one screw holding the enclosuer, then unplug the wire harness, remove 4 screws holding the solinoid, and the 4 screws holding the auger motor. The hardest part was removing the auger from the shaft of the motor. this took most of the time. reassembly went very fast.

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

Had to disassemble ice maker to install part. . .

I removed the water filter located in the refrigerator and replaced it with the bypass plug. The ice cubes and the water dispenser work properly . I am pleased with the outcome especially the price was only $15 and less than 5 minutes of my time. Maytag recommends replacing the water filter every six months at $40 a filter. One can see how this will add up in time. Eventually I am installing an after market water filter in line prior to the refrigerator.