NNT156GZ3A (7D11A) Maytag Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Craig from Westminster, CA
- Parts Used:
- WP61002140
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
cocktails running out of ice
filled both ice cube trays up with water and placed in the freezer.. within hours my ice oproduction was doubled! no more warm cocktails : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert from Water View, VA
- Parts Used:
- WP70048-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Old gasket was ripped, damaged
1. Remove food from door
2. Remove bottom hinge from door. Make sure door is supported. Shoulder works nicely for that. 3 hex head screws
3. Drop door down and off. Lay on table.
4. Remove inside door panel. The hex head screws require a 1/4" socket, and there are a lot of them, concealed under a flap of the gasket. Lift off and clean inside door panel.
5. The old gasket peels off. The new one goes on the same way. Place the inside door panel back on the door, and install the screws at the corners first. Make sure that they go thru the holes in the gasket.
6. Lift the door into position. Install the hinge, holding the door. Once it is tight, you are done.
2. Remove bottom hinge from door. Make sure door is supported. Shoulder works nicely for that. 3 hex head screws
3. Drop door down and off. Lay on table.
4. Remove inside door panel. The hex head screws require a 1/4" socket, and there are a lot of them, concealed under a flap of the gasket. Lift off and clean inside door panel.
5. The old gasket peels off. The new one goes on the same way. Place the inside door panel back on the door, and install the screws at the corners first. Make sure that they go thru the holes in the gasket.
6. Lift the door into position. Install the hinge, holding the door. Once it is tight, you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C MARTIN from TAMPA, FL
- Parts Used:
- WP61002140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace broken ice cube trays
No repair needed. I had only to wash the new ones and use them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from TANEYTOWN, MD
- Parts Used:
- WP52185-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Pantry Drawer Cover keeps falling off, not held in place by End Cap Kit
I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabinet on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.
Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.
Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.
Was this instruction helpful to you?
Thank you for voting!