GT2128PVCW Maytag Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Boulder City, NV
- Parts Used:
- WP67002190
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
A plastic drawer guide broke.
The drawer guide mounts in slots on a bracket hanging below the shelf above. Only had to use a screwdriver to move the plastic tab in the slotted bracket then slide the whole plastic guide out. ordering the new one was easy, cheap, and quick through PartsSelect.com. The new part just popped in without tools. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Nantucket, MA
- Parts Used:
- WP67002191, WP67002190, WP61002308, WP61002307
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rack rollers on each guide had broken off.
1-Removed drawer; removed drawer shelve which contained rails; slid old rail out of shelve mounts with light taps on ends.
2- Screwed on the new rollers to rail guides; reinstalled new guides into shelve mounts; re-installed shelve onto mountings in refrigerator; re-inserted drawer nto new rails-Done!
Received parts 48 hrs. after placing order!
Great job! Third positive experience with Parts Select.
2- Screwed on the new rollers to rail guides; reinstalled new guides into shelve mounts; re-installed shelve onto mountings in refrigerator; re-inserted drawer nto new rails-Done!
Received parts 48 hrs. after placing order!
Great job! Third positive experience with Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from ORANGE PARK, FL
- Parts Used:
- WP61004010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Old seal was pulling apart, door wouldn't seal tight.
Having 2 people makes the job a snap. On our model the freezer door had to be partially removed so the other door can be lifted off, then slightly tighten freezer door in place. Lay door flat and remove the 36 screws & gasket making sure the new gasket slots are tucked under to match up with screw holes. We started all the screws & came back and tightened firmly. Loosen the freezer door and set the bottom door back in place, make sure doors clear each other and tighten down. Finished! I took the advice of another post and put gasket in clothes dryer for about 5 minutes,helps a bunch. Start to finish,30 minutes. Taking food out of door & replacing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennie from ASHEVILLE, NC
- Parts Used:
- W11618980
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The lightbulb burned out
Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from San Antonio, TX
- Parts Used:
- WP67002191
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Adjusti-temp meat/cheese drawer right glide rail fell off
When the new glide rail didn't look any different that the one I thought was broken, I thought I'd assessed the wrong broken part as everytime I tried to put it in the slots it would still fall off, just like the old one.. But I went back and reread the other repair stories to get a picture in my mind what they were talking about. I realized I needed to get the glass shelf off but it wouldn't budge. I found the original information booklet and realized the two blue clips in the shelf tracks were nothing more than packing clips (we've had the fridge 8 year.) when I got those off (these took the most time and a flat head screwdriver) the shelf came right off. Then I put the glide rail brackets in the appropriate slots, pushed the rail toward the front of the shelf and when it got to the place of resistance, I just applied steady, gentle pressure to get the brackets to lock in place in the slots. Repair done, placed shelf back in fridge, put drawer back on, and it was done. Oh, forgot, I first had to take the little wheel thingy off the old raid and screw it onto the new rail before attaching the new rail to the shelf. By the Way, this was really easy to do. I'm a 66 year old grandmother and this was my first refrigerator repair. Always read the previous repair stories--they really do tell you what you need to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hemet, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WILLARD, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
defective light switch
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from HIGBEE, MO
- Parts Used:
- WP61002623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke the crisper glass shelf while cleaning my refrigerator.
This replacement glass shelf arrived the very next day-after it was shipped. I was so impressed with the easy method of ordering and the prompt delivery of this product-also, the quality of the shelf was perfect. Great service!! I would recommend this for everything-as far as parts needed for repair or replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C MARTIN from TAMPA, FL
- Parts Used:
- WP61002140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace broken ice cube trays
No repair needed. I had only to wash the new ones and use them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucien from Cambridge, MA
- Parts Used:
- 67764-1
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Identifying the part on the parts diagram took the longest. Finding the screw driver bit that would remove the old screw that held the original shelf support took longer than the actual repair.
Once I identified the bit that would remove the screw, the rest of the repair took 5 minutes. I removed the screw and discarded the remains of the original but now broken shelf support. With the same screw I simply attached the new shelf support that I received from PartSelect.com. End of story.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from ATLANTA, GA
- Parts Used:
- WP61004009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
The freezer was icing and the refrigerator was running constantly
I took the freezer door off. Gasket screws ran on the four side of the door. I unscrewed the top and three sides but the bottom screws were completely rusted and stuck. As the refrigerator was almost 19 years old which is the predicted lifespan I decided to just buy a new refrigerator. I was able to adjust the old gasket and got the freezer working normally but decided to go ahead with the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from NEW HARTFORD, NY
- Parts Used:
- WP67002190
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Had to be careful not to break other parts.
Popped rail off and replaced with new one. Video showed how to do it. A bit tight to remove and just needed a little strength and patience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitchell from Lilburn, GA
- Parts Used:
- 67002189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Meat Pan Cracked
Snapped it together and slid it in...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!