GC2227SDFB Maytag Refrigerator - Instructions

googled for answer, deduced relay/switch problem. googled again for parts, found partselect.com, ordered part. 2 days later & $70 lighter, my 8yr old Maytag was working again! Parts were good fit, instructions were decent enough. Not for inexperienced tinkerer though.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

took off door and replaced parts and replaced door

Removed top hinge cover. With nut driver, removed the three screws that held top hinge. Gently lifted door off bottom hinge and laid door across sawhorses. Once I saw what parts were worn on bottom hinge, removed them. Was a little confused from parts diagram online to what I had in my hand and needed to put back on door. After a few minutes realized I had ordered basically a duplicate part, "closer with cup", didn't need it. With a screw driver easily replaced new parts and reassembled the door. Works great.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

The driver that turns the screw broke off the ice enclosure. I removed the side panel, removed one screw underneath the enclosure, unclipped the wire harness and removed the entire enclosure.

I did one unnecessary step and removed the magnet from the housing. Better to remove the entire housing, then transfer the motor and magnet to the new housing.

I noticed that others had problems unscrewing the drive unit (which you need to do to transfer it to the new housing.) I simply held the center hub with a pair of pliers, and gave the drive one tap with a hammer. Like the other reviews, note that it unscrews opposite way.

Reassembly was quicker and easier; just undo everything you did to get the housing out of the freezer.

Removed the four screws around the shaft. Removed the support nut on the underside of the enclosure. Pulled the enclosure out of the freezer. Removed the "blade" from the drive shaft - This was somewhat difficult as others have described. Needle-nose vice grips are almost a requirement or you'll never get it off. (Turn clockwise to remove it, as the threads are reversed). Attached the motor to the new enclosure with the four screws. Replaced the enclosure and screwed in the support nut on the underside. The difficulty in this whole process by far is removing the blade from the shaft. It takes a lot of force. At one point I almost gave up thinking that it was manufactured or pressed on. It finally came loose, and then the reinstall was no problem. My suggestion would be to let the motor and parts heat up to room temperature for a bit. It may help. A little spray of WD-40 may help as well.

This is an easy repair. It took me longer to remove the bins off the inside of the door and clean then up, then the actual repair. Remove the top hinge trim 1 Phillips screw. After the hinge trim is removed you'll see 3 hex screws. Remove the 3 screws. Hold and open the door half way, and lift up on the door. The door is not heavy. Use your kitchen table as a work bench. Place the door flat on the kitchen table . On the bottom of the door you'll see the "CLOSER" One screw removes it. Reverse operations and reassemble. Note: Put a little Vaseline grease on the pivot point. Thats it ... 15 minutes and your done plus you saved a $65.00 service call.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

It was simple and the fridge looks brand new.

First I removed the top hinge cover plate. Then removed the three screws in the top hinge. I lifted the door off the lower hinge and laid the door on the kitchen counter. I removed the one screw holding the natural door closer part from the bottom of the door and installed the new part with the same screw. I then replaced the lower hinge pin with the new one. It just sets in place. I then repositioned the door and reinstalled the top hinge. the whole job took about 15 minutes after the refrig door had been emptied. The door works like new.

opened door, put in shelf then closed door

This was the easiest project of the Holidays. Literally saw the part was broken, went on-line and ordered the part and in a few days it arived at my door. Removed a few screws, unplugged the electrical connector and transfered the motor to the new part.

Saved me a few hundred dollars the repairman would have charged!

THANKS

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Removed all 50 screws and replaced the seal. The door still comes open a tad but now it seals all the way. This was my first and last Maytag.