NS208MA (DR07A) Magic Chef Refrigerator - Instructions

Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cable wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!

Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.

I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.

Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.

Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)

Just kept working on it.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

I watched the repair video on the web site a couple of times just to get comfortable with what to expect. (i.e. pressing tabs on wiring harness to remove, placement of lift arm for removal and installation) These instructions were a big help...I had the removal, modifications and installation completed in less than 30 minutes. Ice cubes (without the extra icicles) in 1 hour...

The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!

Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice maker. Gregg in PA.

I watched the video regarding the instillation of this ice maker a few times and then followed it exactly. It was incredibly easy. We had ice cubes about two hours later and no longer had a leak making icebergs!

Removed top drawer from freezer. Unplugged the ice maker. Uncrewed the bottom screw. Loosened the two top screws. Removed old ice maker. Removed all the parts that didn't come with the new ice maker and installed on new ice maker. Reinstalled the new ice maker. Started making ice with no leaks in about 3 hours.

I have a Maytag Refridgerator with lower freezer and ice maker. Stopped making ice. Noticed the unit would fill up and freeze but the tray wouldn't rotate to drop the cubes into the tray. Cleared the frozen trays to see if it was just stuck but same thing happened. Replaced unit, not difficult with the exception that the top tray is ridiculously hard to get out. Never did do it, just worked around it. Working perfect now.