CTB2126ARW Magic Chef Refrigerator - Instructions

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

When that one came and I went to install it, I found that my fridge was so old (almost 30 years) that the wire harness on the old icemaker could not be transferred to the new one. The old one was hand wired into the guts of the machine with wire nuts and other connectors. The new unit needs a plug in harness to match a plug connection on the ice maker. Also, the bent wire arm that senses ice bin levels was different, old unit hooked in with clips and such, new one pops into a socket in the new ice maker.

I called PartSelect back again, and the clerk spent a lot of time in the books (no parts in the online listings) and found new style connector and wire arm. Another 25 dollars and problem is solved.

Once those parts came, the actual installation was a breeze. Remove three screws, unplug the ice maker from the back wall of the fridge, plug new wire harness into new ice maker and the back wall of the frige, install new ice maker with the same three screws, pop the new style bent wire arm into place and pop the plastic cover from the old ice maker onto the front of the new one. Done! Took me ten minutes (plus two weeks of chasing parts, but only half an hour of actual time in those two weeks).

I let it make a couple of loads of ice that I disposed of (to capture any dust and crud that might have been on or in the new ice maker) and then turned it loose. We had a nice full bin of ice in the morning.

First had to remove baskets and door from freezer. Removed three screws; removed old ice maker; Attached new ice maker with three screws; removed arm from old ice maker and placed in the new ice maker. Replaced door and baskets

Followed the instructions in the video provided via email from Partselect
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.

Since it was an older appliance I decided to replace the whole ice maker assembly. I carefully disassembled the old one and then installed the new one. piece of cake.

removed screws, pulled element out, and put new element in

unscrewed the 3 nuts, took off the electrical connection. Then put new one on. One problem, the ice maker had a hole on the side for the hose, mine needed one in the back. I used tape to hold it in place going over the part that was in the wrong place.

The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!

I watched the repair video on the web site a couple of times just to get comfortable with what to expect. (i.e. pressing tabs on wiring harness to remove, placement of lift arm for removal and installation) These instructions were a big help...I had the removal, modifications and installation completed in less than 30 minutes. Ice cubes (without the extra icicles) in 1 hour...

Removed top drawer from freezer. Unplugged the ice maker. Uncrewed the bottom screw. Loosened the two top screws. Removed old ice maker. Removed all the parts that didn't come with the new ice maker and installed on new ice maker. Reinstalled the new ice maker. Started making ice with no leaks in about 3 hours.

Adding water to Ice Maker, caused ice to be made. I assumed the Single Outlet Water Valve to be problem (despite %4 probability). I suppose problem could have been in the ice maker itself and it's interface to the Single Outlet Water Valve but fortunately the Single Outlet Water Valve solved the problem. The Parts Select replacement part video was very helpful and the replacement was fairly easy. Were the problem in the Ice Maker itself, I don't know that I could have justified the cost of the the repair for a 17 year old refrigerator.

I watched the video regarding the instillation of this ice maker a few times and then followed it exactly. It was incredibly easy. We had ice cubes about two hours later and no longer had a leak making icebergs!

I have a Maytag Refridgerator with lower freezer and ice maker. Stopped making ice. Noticed the unit would fill up and freeze but the tray wouldn't rotate to drop the cubes into the tray. Cleared the frozen trays to see if it was just stuck but same thing happened. Replaced unit, not difficult with the exception that the top tray is ridiculously hard to get out. Never did do it, just worked around it. Working perfect now.

ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed readily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.

First i used a nut driver to remove the bottom screw, the unclipped the two top clips by leaningthe bottom of the unit outwards. I used a mirror to see the two top clips as i could not see inside. Then i removed the wiring harness from the refrigerator. The unit came right out, i transerred the needed parts, and re-installed. Not too bad - about 45 mins. It works great!