RD22DA-3A (4M49B) Magic Chef Refrigerator - Instructions

Moved fridge out from wall, unplugged power cord. Laid on floor, removed 6 screws from cover. Removed one threaded bolt to allow assembly to slide out. Removed special nut, and took fan off. Removed 3 motor mounting bolts. Unscrewed 2 wire nuts, and untwisted wires. (option 1, no ground) Vacuumed entire area around motor. Used 3 bolts to mount motor to holder assembly, and special nut to install fan. Stripped wires back about 3/4 inch. Twisted two wires together CW, and installed new wire nuts. Slid motor assembly back into slot,(keep wires away from blades) and used one threaded bolt to secure assembly. Reinstalled cover plate with 6 screws. Plugged power cord in to test air flow (out through cover vents). Moved fridge back into place. The loud whirring noise did not stop for a day; then quiet!

Unloading the freezer and removing the back panel were the most time consuming aspect of this repair. Many models only have 4 screws, but this one has 9, and being a side by side it was a tight fit to reach them. Once defrosted we tested the thermostat, found it "dead", and ordered a new one. The part came within 3 business days. Installing it took minutes, since we had not permanently screwed in the back panel again. We didn't want to reload everything until we knew things worked properly, so we didn't put everything back right away. We thought we had further problems as the freezer got really cold but the frig still didn't get down to temp. Turns out we just needed to reinstall the fan shield which we'd taken off along with other parts to access and check the vents. The fan shield must be in place to direct the cold air into the vent to the refrigerator. Duh! It was an oversight that once caught made total sense! Now all works fine on this 20 year old Maytag side by side!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip the insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.

Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.

I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!

Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and it works like its brand new. Thank you PartSelect!

My Son who is not an appliance repairman did it for me. He had some difficulty getting the nuts and bolts loose mainly. Sorry I'm not much help other than that! I would like to compliment you on your fast service, first time ordering from you and it was for an older model refrigerator that my repairman said he couldn't find. It's working fine now and I'm a satisfied customer!

Having watched the Maytag technician perform this same repair a few years ago, I was sure I could do it myself! The take down was quite easy. The actual repair was a little more difficult, as there isn't much space to work in. Others have posted their procedures and mine was no different, so I won't repeat what has already been said, other than to add that when I installed the heater assembly, I dropped a length of string ( with a small nut on the end for weight) down the inside of the cabinet alongside the evaporator, and tied the wiring to the string and pulled it through to the top. That metal flange and those fins on the evaporator are very sharp! I'm not comfortable working in gloves, so if you are, I suggest you wear them... The thermostat was simple 'plug and play'! The refrigerator/freezer is working fine now. Thanks to y'all at PartSelect for your prompt shipping of the parts that I ordered.

First, watched video on Part Select Website. Very good. Pulled Appliance out from wall, Pulled the power plug, and removed the back shield covering the working parts of the unit. Found the fan and it was almost the same setup as on the video except that I could not get to one of the screws holding the motor in place so had to remove the entire bracket with the fan. Not too hard. Cleaned away dust and gunk around the site and noticed that the fan pulled air through a tunnel-like condenser coil that was packed with gunky lint...this is what probably killed the motor. I cleaned out the tunnel with the bottle brushes and vacuum and installed the new motor / bracket assembly. Then replaced the shielding around the fan and the back cover .panel. This is important because these form the channel that guides air flow throughout the condenser coils. This particular refrigerator has a barrier underneath which guides air flow from the front left to the condenser, through the fan, over the evaporator drip pan and out the right front. I cleaned all the lint and gunk from this area as well. I also made an air filter (cut from a furnace filter) and wedged it in front of the air entry section. This should keep the condenser coil cleaner over time but you have to remember to change the filter once a year. Probably should clean the condenser coil every 5 years as well. This unit has been very reliable over 20 years and may well go for another 20. Good luck with your repair.

I folded in half twice! and took the back off the fridge(cardboard) and took one brace off and just took the screws off the fan from the other two braces. Turned the fan enough to get at the wires for the fan and cut them off an inch from the old fan, stripped the insulation and wire nutted them to new fan. Make sure they don't interfere with the new fan and put the new fan in place put the screws in and we're making ice and cold fridge again.

I removed the cover that protects the freezing tubes, they were frozen solid,used my heat gun to melt away the ice, being very careful not to burn any wires. Then I removed the old heating coils,connected the new ones, replaced the cover and I was done. The thing that took the most time was melting the ice, you cant do it in a hurry because you may burn wires

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.

just had to remove the fan motor the hard thing is getting down to it

Pull box out ""unplug box"" empty frezer including storage baskets,place ice maker in off remove ice cube box, do not remove ice maker, useing nut driver loosen side rail screws about 1/4"slide basket rails in or out and pull to center of box should slip off screws, remove light bulb cover & bulb, remove 4 screws holding ice worm drive motor "" hold "" will fall it is atached to a electrial plug un plug and lay aside,unscrew back panle screws 4 left 4 right on back cover, " remove hiden screw at top center of back panel and pull up and pry out at bottom silde out downwerds,remove cross plates one center one bottom these hold defoster bars, unwind wires center defroster bar somewhat difecult bottom one just slide down unplug from panel at top behind where ice cube drive was located, replace new defroster assm reasemble defroster bars into cross bars wind in & plug up new wires behind cooling fins being carefule not to cut or nick wires of bend cooling fins replace screws,wires are 1 small plug 1 large,reinstall back panle top center screw first don't tighten aline side screw holes replace side screws then tighten top screw. Replace drive motor being sure to conect,replace bulb,bulb cover,side railes,bens,ice cube box & put ice maker lever in on poss. Plug box in weight 8 to 10 hours with box set at mfg 's starting settings. Should work like a charm.