RB17HN2AF (9B53A) Magic Chef Refrigerator - Instructions

I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.

Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.

Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

I performed basic troubleshooting to make sure there was power and water. Based on historical research on this particular ice maker, I decided that the best direction was to replace the entire assembly. I found this item on this site, ordered it and received it a few days later. I basically removed the ice pan and a few items in the freezer, removed the three mounting screws with either a flat blade screwdriver or nut driver, pulled the electrical harness out of the back wall of the freezer and transferred it to the new ice maker and then installed the new unit, really that simple. Iwas concerned at first, not seeing any activity in the new ice maker but after 15 minutes or so I heard ice falling into the ice bin. Well worth replacing seeing how simple this job was.

Saw many photos on the Internet that looked like my ice maker, but they were different. I put in my Refrigerator model No. and found my exact replacement ice maker right away. I was a little cautious, because the new one didn't include the wiring harness, or the plastic cover. I took the chance and ordered it. Super fast delivery, a Day or 2 at most. Everything went smoothly, and after the new one was in, I crossed my fingers until the timer kicked in, and I started hearing ice cubes falling in the tray about 3 hours later. Success! I had been having problems with the ice maker almost from the beginning. Hopefully, the replacement will last longer. I will say that this Maytag Fridge. is the absolute worst kitchen appliance I've ever owned in my 47 years of house keeping! The defroster went in the freezer a couple of months after the Warranty ended, and it cost me $375.00 to have a Tech, come in to repair. I got away easy this time, buying the ice maker for $135.00 and being able to do the work myself.

Jim

removed screws, pulled element out, and put new element in

This was a very easy fix. I took the old ice maker out, including the electrical harness. Switched the harness and stop bar to the new ice maker on my bench, then installed the new assembly. Ice initially had some hollow cubes. I checked the ice maker for level. But it was fine. Thought it might be moving too fast. But it seems to have cleared up. Perhaps it took some time to completely cool down.

Removed the elec connection (after unplugging app) found it easier to remove from appliance. Remove the three screws ( do not temove,....just loosen, the top two) bottom must be removed! Insert the power connection, exchange the tilt up rod, line up the water connection and place back on the two top screws. Tighten and relpace the bottom screw. I found out the hard way.... you cant't see the two top screws . The slots on the ice maker just fit over the screw heads.... it's cold in there!!!

Hopoe this helps..

Cape Cod

Bought ice maker and new harness. Had to buy harness because of water damage. Took out the three screws that attached the ice maker and removed old leaky ice maker. Detached old harnees. Attaced new harness to new ice maker and put on back on with the three screws. Had ice in about 30 minutes. So easy to do!

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

Removed old icemaker by removing two hex screws and one phillip's head screw.

Disconnected power connection to refrigerator.

Removed power connection harness and ice level sensor arm/levor and cover from old ice maker and installed on new ice maker.

Re-installed in refrigerator. It was simple on this model.

removed old and instaslled new. biggest problem was getting to one of the screws.

I disconnected power, turned off water supply, removed three hexhead screws, disconnected wiring harness plug, then reversed procedure. New icemaker seens to be a little slower in making cubes. However, the cubes are clean, perfect shape and THEY DO NOT CONTAIN ANY OF THE BLACK COATING AS THE OLD ICE MAKER CAUSED. THIS WAS A FAIRLY SIMPLE TASK.