CTF2126ARW Magic Chef Refrigerator - Instructions

Had to remove the freezer door. Held on by 4 screws. Removed bottom screw on old icemaker and loosened the top 2. Slid the old icemaker up, removed the wiring harness and installed it on the new one. Took the wire out that turns the icemaker off and installed it on the new one. Hooked new icemaker on 2 screws, installed bottom screw and installed freezer door. Turned water back on and started making ice.

Repair done according to video and instructions. What you need to know is myself and my husband are adverse to all kinds of "simple" repairs because they never go well and we are not handyman kind of persons. This, I must say, was a delightful change in our typical experience of attempting to make our own repairs.
Thanks
Sandy

I have a Maytag Refridgerator with lower freezer and ice maker. Stopped making ice. Noticed the unit would fill up and freeze but the tray wouldn't rotate to drop the cubes into the tray. Cleared the frozen trays to see if it was just stuck but same thing happened. Replaced unit, not difficult with the exception that the top tray is ridiculously hard to get out. Never did do it, just worked around it. Working perfect now.

ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed readily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

First i used a nut driver to remove the bottom screw, the unclipped the two top clips by leaningthe bottom of the unit outwards. I used a mirror to see the two top clips as i could not see inside. Then i removed the wiring harness from the refrigerator. The unit came right out, i transerred the needed parts, and re-installed. Not too bad - about 45 mins. It works great!

unscrewed the 3 nuts, took off the electrical connection. Then put new one on. One problem, the ice maker had a hole on the side for the hose, mine needed one in the back. I used tape to hold it in place going over the part that was in the wrong place.

Unplug fridge, close off water supply valve. Remove two screws attaching assembly to freezer wall, detach wiring harness. Remove parts from old assembly: wiring harness, shut-off rod, harness clamp and attach to new assembly. Connect wiring harness, two screws attach new assembly to freezer wall. Plug in fridge and open water supply valve (after an opportunity to change in-line filter). Works now!

First i removed the three screws that held the assembly to the fridge, then removed the water flow tube from ice maker. 2- flipped ice maker over ,then used a small flathead to push in locking tab that held wire harness and out comes ice maker. All though the water cup was not quite the same i used the old ice maker to take apart to see how it was put together,hopeing there wasn't a myriad of parts. -NO INSTRUCTIONS- piece of cake, don't take out outside screws,take out the 2 inside screws-these srcews hold the guts to the water tray-pull apart and reassemble the unit after you have switched the cups. then reinstall into fridge with your outside cover and the full bin wire and your done. It helps to be alittle mechanicly inclined. -NO GUTS NO GLORY,DONT BE AFFRAID TO LOOK OUTSIDE THE BOX-

Piece of cake. Removed two screws, pivoted old ice make up, lifted it out of the mounts. Installing the new one was just the reverse.

Identifying the correct replacement ice make was easy also, due to the photographs on PartsSelect.com

I removed the old icemaker, took it out to my shop & removed the wiring and etc. and put it back in place.

Followed the other directions -- I have the bottom tray freezer. It was really easy to unscrew the screws -- a bit of a reach to get them all, but not a problem. Leave the top screws half-way in and it's a bit easier (the icemaker has the brackets that just sit on the screws). Thanks to everyone who left instructions!

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

First, I removed the ice bucket. Then I removed the two top left screws and bottom screw with a 1/4 inch nutdriver. I pulled the assembly out as far as the wiring harness would allow, disconnected the harness on the lower left side, and removed the unit. I removed the old motor cover and ice stop wire and placed them on the new unit. I then reversed the process. It went so fast that the freezer must have still been close to zero degrees because it filled with water within 15 minutes.

I popped out the old switch with a screwdriver pressing down the tab on the bottom and unplugged the terminals. Then I plugged in the new switch and popped back into the socket. Piece of cake!