RB21KW4AF Magic Chef Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Charleston, SC
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Quit making ice
Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Golden, CO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from green bay, WI
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
icemaker quit working
I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MARYLAND HTS, MO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
freezer (later fridge too) wouldn't stay cold~
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Stone Mountain, GA
- Parts Used:
- 12002087
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced refrigerator light assbly
replacement was relative easy. The problem came with wire connector that had to be cut, stripped and crimped. The crimping was the dificult part. the connector was a problem to crimp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Las Cruces, NM
- Parts Used:
- D7824706Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
difficulty unplugging the power pigtail
Just kept working on it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from Indianapolis, IN
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker Leaked Creating an Ice block
Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Bloomfield Hills, MI
- Parts Used:
- 4318047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Old Valve was dead
This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from Aurora, NC
- Parts Used:
- D7824706Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
ice maker quit working
Since it was an older appliance I decided to replace the whole ice maker assembly. I carefully disassembled the old one and then installed the new one. piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from LEXINGTON PK, MD
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
No cold
Like you video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FORD CITY, PA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer occasionally had a temperature alarm.Clicking noise also.
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORTH HAVEN, CT
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Not all ice cubes were coming out of tray. Water was freezing from maker into cube catcher
Remove bottom screw loosen 2 top screws unplug connector from back of icebox. Lift up and pull forward. Swap front cover full bucket stop bar and wire (plugs in) reinstall 10 minute job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MILFORD, CT
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
not making ice
the diagnosis was the most difficult step.. and trusting that the one visible nut was the only thing holding it on.. (there are 2 other clips that you need to use a little force on to detach). remove the ice maker (one nut, 2 clips, detach plug).. then remove the 3 screws holding on the 'face' , pry face off, you will see where the 'contact' has burned/melted/worn away. replace unit. 80% of the time, this is the problem (according to my research)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary L. from Millsboro,, DE
- Parts Used:
- WP627843
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sandra from Scottsdale, AZ
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Ice maker not making ice
Repair done according to video and instructions. What you need to know is myself and my husband are adverse to all kinds of "simple" repairs because they never go well and we are not handyman kind of persons. This, I must say, was a delightful change in our typical experience of attempting to make our own repairs.
Thanks
Sandy
Thanks
Sandy
Was this instruction helpful to you?
Thank you for voting!