RB151PFW Magic Chef Refrigerator - Instructions

Five minutes with a phillips screw driver and the cube maker was changed. . . In the process, I failed to unplug the unit, and shorted the fill valve in the back. Again, five minutes with a nut driver and it was changed. No need for a PHD or the cost of a service technician for either job.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

I tilted the unit back enough to scew the new legs into the threaded holes.

Had to remove the freezer door. Held on by 4 screws. Removed bottom screw on old icemaker and loosened the top 2. Slid the old icemaker up, removed the wiring harness and installed it on the new one. Took the wire out that turns the icemaker off and installed it on the new one. Hooked new icemaker on 2 screws, installed bottom screw and installed freezer door. Turned water back on and started making ice.

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

Removed old icemaker by removing two hex screws and one phillip's head screw.

Disconnected power connection to refrigerator.

Removed power connection harness and ice level sensor arm/levor and cover from old ice maker and installed on new ice maker.

Re-installed in refrigerator. It was simple on this model.

Saw many photos on the Internet that looked like my ice maker, but they were different. I put in my Refrigerator model No. and found my exact replacement ice maker right away. I was a little cautious, because the new one didn't include the wiring harness, or the plastic cover. I took the chance and ordered it. Super fast delivery, a Day or 2 at most. Everything went smoothly, and after the new one was in, I crossed my fingers until the timer kicked in, and I started hearing ice cubes falling in the tray about 3 hours later. Success! I had been having problems with the ice maker almost from the beginning. Hopefully, the replacement will last longer. I will say that this Maytag Fridge. is the absolute worst kitchen appliance I've ever owned in my 47 years of house keeping! The defroster went in the freezer a couple of months after the Warranty ended, and it cost me $375.00 to have a Tech, come in to repair. I got away easy this time, buying the ice maker for $135.00 and being able to do the work myself.

Jim

Repair done according to video and instructions. What you need to know is myself and my husband are adverse to all kinds of "simple" repairs because they never go well and we are not handyman kind of persons. This, I must say, was a delightful change in our typical experience of attempting to make our own repairs.
Thanks
Sandy

unscrewed the 3 nuts, took off the electrical connection. Then put new one on. One problem, the ice maker had a hole on the side for the hose, mine needed one in the back. I used tape to hold it in place going over the part that was in the wrong place.

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

First i used a nut driver to remove the bottom screw, the unclipped the two top clips by leaningthe bottom of the unit outwards. I used a mirror to see the two top clips as i could not see inside. Then i removed the wiring harness from the refrigerator. The unit came right out, i transerred the needed parts, and re-installed. Not too bad - about 45 mins. It works great!

ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed readily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."

I have a Maytag Refridgerator with lower freezer and ice maker. Stopped making ice. Noticed the unit would fill up and freeze but the tray wouldn't rotate to drop the cubes into the tray. Cleared the frozen trays to see if it was just stuck but same thing happened. Replaced unit, not difficult with the exception that the top tray is ridiculously hard to get out. Never did do it, just worked around it. Working perfect now.

First had to remove baskets and door from freezer. Removed three screws; removed old ice maker; Attached new ice maker with three screws; removed arm from old ice maker and placed in the new ice maker. Replaced door and baskets