IMKTM Magic Chef Refrigerator - Instructions

Remove bottom screw loosen 2 top screws unplug connector from back of icebox. Lift up and pull forward. Swap front cover full bucket stop bar and wire (plugs in) reinstall 10 minute job

the diagnosis was the most difficult step.. and trusting that the one visible nut was the only thing holding it on.. (there are 2 other clips that you need to use a little force on to detach). remove the ice maker (one nut, 2 clips, detach plug).. then remove the 3 screws holding on the 'face' , pry face off, you will see where the 'contact' has burned/melted/worn away. replace unit. 80% of the time, this is the problem (according to my research)

Removed old ejector arm and installed new part.

Five minutes with a phillips screw driver and the cube maker was changed. . . In the process, I failed to unplug the unit, and shorted the fill valve in the back. Again, five minutes with a nut driver and it was changed. No need for a PHD or the cost of a service technician for either job.

It was real easy. I unpluged the fridge. Took out the three screws that held the icemaker to the wall. Unpluged the wire harness. Removed the old icemaker and reversed the order to install the new one. Everything lined up perfectly.

Removed two screws on top. Then one under the ice maker ,held on to it while I unpluged the white flat plug. Then installed new one in reverse. Of course re-connect power wires on.
I turned power off at fuse box.
First batch of ice in an hour or so.

First i removed the top two screws that help the ice maker in place then remove the bottom screw, then unplug unit from freezer, removed ice maker for freezer, took out wire harnes, put wire harnes in new ice maker, plug new unit in place the unit in freezer and put in the bottom screw, them align the top two screw and but them in and was done. Check ice maker in two hours and there was new ice being made.

First, unplug power to Fridge, then remove ice bin and set to one side, then remove the clip that holds the fill tube down by pulling up on it, and remove the fill tube. Remove the two top screws on ice maker assembly first, as the bottom screw will support unit. Then remove the single bottom screw. Rotate the Ice Maker slightly down and this will expose the electrical connector. With a short, small, flat head screwdriver in your left hand, depress the locking tab for the connector, while your right hand supports the assembly and pulls the connector outward to disconnect. Remove old Ice Maker, and remove the bin full lift wire, it's a slide in fit and install in your new unit. Check your fill tube water diverter on the right side of Ice Maker unit , you may need to remove the blank, it is U shaped and molded for easy removal, but use caution when removing to be on the safe side, this allows the fill tube to go down into the diverter, Re-Assemble in reverse order. Give the unit plenty of time to reach proper operating temp, and cycle. Make sure and discard your first Ice cycle.

Piece of cake. Removed two screws, pivoted old ice make up, lifted it out of the mounts. Installing the new one was just the reverse.

Identifying the correct replacement ice make was easy also, due to the photographs on PartsSelect.com

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

I simply removed the 3 screws holding the unit into the freezer with a nutdriver, then disconnected the power plug (a little hard to get to, and requires releasing a small tab in a hole in the main body). The icemaker came right out with no problem. I then had to change out the water funnel inlet because mine had a different style than the one provided on the new one. This was easy also, just remove 2 phillips head screws that are set deep in 2 holes in the face of the motor drive unit, then pull the whole assembly apart far enough to allow the ejector blades to slip out of the hole through the inlet funnel, then snap the funnel loose to move it to the new one (the same technique to be used on the new one, then re-assemble in reverse order).

very easy, 3 screws,took old one out, take 2 inter screws out (of ice maker) of old unit to replace water feed cup on new unit very easy,installed had ice after 12 hrs.

Turn off water, removed two mounting screws, unplugged solenoid, removed incoming water connection and plastic pipe to ice maker. Installed new valve, connected water lines, reconnected plug, remounted with screws. Turned water back on, over rode power to ice maker and checked for leaks. Total time about 5 minutes. Very easy repair.

very simple,remove old and unplug install new,three screws, used old hose clip.

First, I removed the ice bucket. Then I removed the two top left screws and bottom screw with a 1/4 inch nutdriver. I pulled the assembly out as far as the wiring harness would allow, disconnected the harness on the lower left side, and removed the unit. I removed the old motor cover and ice stop wire and placed them on the new unit. I then reversed the process. It went so fast that the freezer must have still been close to zero degrees because it filled with water within 15 minutes.