8C44A Magic Chef Refrigerator - Instructions

The old water valve leak required me to purchase this new complete part. After shutting off the water supply, disconnect the supply line, take out the old water valve by disconnecting the "plug" from the refrigerator, and disconnect the plastic water line going into the ice maker. Then just reconnect the new water valve by plugging it into the 2 pronged receptacle, note to be sure to write down which wire goes into which input when disconnecting the old valve. Then hand tighten the plastic tube into the valve. Next attach your water supply line into the new water valve, tighten this supply line as you would any plumbing supply line with a couple of adjustable wrenches and some teflon tape at the connection. I would also recommend at this point, if the compression fitting on your supply line was like mine a bit old, to spend a couple bucks on a new fitting and put that on the supply line, since you don't want to worry about it being a good seal at the supply line point, once the repair is done. After checking for "no leaks" reattach everything to the rear of the refrigerator (make a note of the attachment before taking out the old valve) and see if your ice maker starts to make some ice. You will hear the valve feeding the water to the icemaker if all is properly setup.

removed all three screws, disconnected power. then I switched out the plug assembly (mine had different male adapter. Then the Control Arm, new arm was to wide and took up to much space when it was fully extended. Put it back in reverse order, and within 5 hours it was making ice.

By watching a video.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

Great service. Unpluged old switch and pluged in new one. Works great

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

Turned off water supply and electricity. Removed old valve by removing two 1/4 in nut screws and water supply line and the ice maker suppy line. Disconnected the electrical line.Reattached water supply line,the icemaker supply line and the electrical connector. Put valve back into refrigerator and attached the two 1/4 in nut screw. Turned on water supply and electricity. Bled water thru system and now have plenty of ice.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Fridge has a top freezer. I unplugged the fridge and removed the lower panel in the back. I removed the two screws that hold the valve bracket to frame of fridge in lower right corner (facing fridge from back). I then disconnected the modular wiring plug and both the water supply and the hose to the icemaker.
i connected the power plug to the new part, reconneced the hose to the icemaker and reattached the bracket with the two screws into the frame of the fridge. finally, i reconnected the water supply and plugged in the fridge. In a few hours the icemaker was working like new. I figure i save about $100 or more by not having to call a repairman and it was easier than I had expected.